Mede hobbyisten, ik ben druk doende mijn kennis op gebied van newcs wat te verbreden. Op dit moment heb ik een smartreader+ in mijn windows config hangen om wat te testen. Het valt mij op dat de conax kaart niet wordt herkend en andere kaarten (nagra2, irdeto2, via2.5) wel, zie hieronder resultaat, mijn vraag wat is de gouden instelling voor conax? Ik heb newcs 1.62 gedownload

Conax kaart:

[ 22:12:05 ] [ Loader ] Reader type 2 on node COM13
[ 22:12:05 ] [ Phoenix ] Opening device COM13
[ 22:12:05 ] [ Phoenix ] Setting parity to ODD on node COM13
[ 22:12:05 ] [ Phoenix ] Setting 1 Stop bit on node COM13
[ 22:12:05 ] [ Phoenix ] Setting baud to 9600
[ 22:12:07 ] [ Loader ] Reset failed ...



Irdeto2 kaart:

[ 22:08:27 ] [ ATR ] T=14 1etu=175.01us Guardtime:17etu WWT:9600etu
[ 22:08:27 ] [ ATR ] Historical bytes: I R D E T O A C S V 5 . 0
[ 22:08:27 ] [ Loader ] Init Irdeto card
[ 22:08:27 ] [ Phoenix ] Setting parity to NONE on node COM13
[ 22:08:27 ] [ Phoenix ] Setting 2 Stop bits on node COM13
[ 22:08:27 ] [ Phoenix ] Setting baud to 5760
[ 22:08:28 ] [ Keyman ] Adding key xxxxx type 0 on Provider 000000 for caid 0604 ID=0
[ 22:08:28 ] [ Keyman ] Adding key xxxxx type 1 on Provider 000000 for caid 0604 ID=0
[ 22:08:28 ] [ Keyman ] Skipping duplicate irdeto
[ 22:08:28 ] [ Keyman ] Adding key FFFFFF type 1 on Provider 000001 for caid 0604 ID=1
[ 22:08:28 ] [ Keyman ] Skipping duplicate irdeto
[ 22:08:28 ] [ Keyman ] Adding key FFFFFF type 1 on Provider 000002 for caid 0604 ID=2
[ 22:08:28 ] [ Keyman ] Skipping duplicate irdeto
[ 22:08:28 ] [ Keyman ] Adding key FFFFFF type 1 on Provider 000003 for caid 0604 ID=3
[ 22:08:28 ] [ Loader ] Card 0604 on port COM13 ready


Nagra2:

[ 22:09:48 ] [ Loader ] Reader type 2 on node COM13
[ 22:09:48 ] [ Phoenix ] Opening device COM13
[ 22:09:48 ] [ Phoenix ] Setting parity to ODD on node COM13
[ 22:09:48 ] [ Phoenix ] Setting 2 Stop bits on node COM13
[ 22:09:48 ] [ Phoenix ] Setting baud to 9600
[ 22:09:50 ] [ ATR ] T=1 1etu=8.96us Guardtime:11etu CWT:139etu BWT:15371etu WWT:153600etu
[ 22:09:50 ] [ ATR ] Historical bytes: D N ? [xx] [xx] [xx] [xx] [xx] [xx] q [xx] G [xx] D N
[ 22:09:50 ] [ Loader ] Init Nagra card
[ 22:09:50 ] [ Phoenix ] Setting parity to ODD on node COM13
[ 22:09:50 ] [ Phoenix ] Setting 1 Stop bit on node COM13
[ 22:09:50 ] [ Phoenix ] Setting baud to 115200
[ 22:09:53 ] [ Keyman ] Adding key 0 type 0 on Provider 000000 for caid 1800 ID=0
[ 22:09:56 ] [ Loader ] Card 1800 on port COM13 ready



VIAccess 2.5

[ 22:13:38 ] [ Loader ] Reader type 2 on node COM13
[ 22:13:38 ] [ Phoenix ] Opening device COM13
[ 22:13:38 ] [ Phoenix ] Setting parity to ODD on node COM13
[ 22:13:38 ] [ Phoenix ] Setting 1 Stop bit on node COM13
[ 22:13:38 ] [ Phoenix ] Setting baud to 9600
[ 22:13:40 ] [ ATR ] T=0 1etu=8.68us Guardtime:12etu WWT:115200etu
[ 22:13:40 ] [ ATR ] Historical bytes: [xx] [xx] [xx] [xx] h [xx] [xx]
[ 22:13:40 ] [ Loader ] Init Viaccess card
[ 22:13:40 ] [ Phoenix ] Setting parity to ODD on node COM13
[ 22:13:40 ] [ Phoenix ] Setting 1 Stop bit on node COM13
[ 22:13:40 ] [ Phoenix ] Setting baud to 9600
[ 22:13:40 ] [ Keyman ] Adding key C13D53B9 type 0 on Provider 000000 for caid 0500 ID=0
[ 22:13:40 ] [ Keyman ] Adding key C13D53B9 type 1 on Provider FFF530 for caid 0500 ID=0
[ 22:13:40 ] [ Keyman ] Adding key C13D53B9 type 1 on Provider 022200 for caid 0500 ID=1
[ 22:13:40 ] [ Keyman ] Adding key C13D53B9 type 1 on Provider 022210 for caid 0500 ID=2
[ 22:13:40 ] [ Loader ] Card 0500 on port COM13 ready



dit is een gedeelte van mijn xml filetje:

<readers name="Phoenix">
<device>
<name>Smargo-Smartreader</name>
<type>smartreader+</type>
<mhz>357</mhz>
<node>COM13</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<!-- <rsa>0000000000</rsa> -->
<irdeto-camkey>0000000000000000</irdeto-camkey>
<irdeto-camkey-data>000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
0000000000000</irdeto-camkey-data>

<crypto-special>No</crypto-special>
<ipk>0000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
000000000000000000000</ipk>
<ucpk>000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000000000000
0000000000000000000000</ucpk>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>15000</newcamd_port>
<autosid>Yes</autosid>
<Seca-PPV>no</Seca-PPV>
<pincode>0000</pincode>
<priority>round</priority>
</device>
</readers>

Met de X86 versie draait de Digitenne kaart met deze settings in de Smargo

<parity>even</parity>
<reset>normal</reset>

bedankt alleen nog niet 100% resultaat maar we hobbyen lekker door -- Card 0B00 on port COM13 failed --

[ 07:26:17 ] [ Loader ] Reader type 2 on node COM13
[ 07:26:17 ] [ Phoenix ] Opening device COM13
[ 07:26:17 ] [ Phoenix ] Setting parity to EVEN on node COM13
[ 07:26:17 ] [ Phoenix ] Setting 2 Stop bits on node COM13
[ 07:26:17 ] [ Phoenix ] Setting baud to 9600
[ 07:26:19 ] [ ATR ] T=0 1etu=104.17us Guardtime:12etu WWT:9600etu
[ 07:26:19 ] [ ATR ] Historical bytes: 0 B 0 0
[ 07:26:19 ] [ Loader ] Init Conax card
[ 07:26:19 ] [ Phoenix ] Setting parity to EVEN on node COM13
[ 07:26:19 ] [ Phoenix ] Setting 2 Stop bits on node COM13
[ 07:26:19 ] [ Phoenix ] Setting baud to 9600
[ 07:26:19 ] [ Loader ] Card 0B00 on port COM13 failed
[ 07:26:19 ] [ Loader ] Starting Newcamd Server on port 15000
[ 07:26:19 ] [ Newcamd ] Newcamd thread Server started on port 15000
^C

Was nog vergeten te melden dat ik de snelheid op 6MHZ heb gezet, misschien krijg je dan wel een juiste init.......

<mhz>600</mhz>

Zou ik niet doen, hij moet gewoon op 358 werken. Waarom gebruik je 357 dolphs? Of is dat in die nieuwe versie van newcs? Ik heb 1.3 nog..

Gebruik je een usb2serial converter?

Ik heb newcs op windows lopen, moet alleen wel debug op "none" zetten anders vertikt ie het te doen. Draai overigens 357.
Ook zappen werkt niet optimonti, maar dit zou ook weleens aan de progdvb plugin wincsc kunnen liggen....

Beste mensen,

Hellup! Ik kom er niet meer uit.
Ik heb ook gedonder met mijn conax kaart onder newcs/linux. Ik hoop dat iemand begrijpt wat er nu precies mis gaat.
Gebruik versie NewCS 1.67 RC1. Als ik initieel opstart is het allemaal prima maar na enkele minuten tv kijken hangt het newcs process ineens. Kan er niet meer bij via de web interface en kan het process ook niet meer killen (zelfs niet met kill -9 ). Ik moet echt de machine opnieuw opstarten om het weer goed te krijgen. Op het moment van 'crashen' zie ik in de logfile altijd een reinit card staan.

[ 21:59:50 ] [ Newcamd ] ECM -> test (OK) [CAID 0000] [Prov 00000000] [SID 000B]
[ 22:00:00 ] [ Newcamd ] ECM -> test (OK) [CAID 0000] [Prov 00000000] [SID 000B]
[ 22:00:10 ] [ Newcamd ] ECM -> test (OK) [CAID 0000] [Prov 00000000] [SID 000B]
[ 22:00:20 ] [ Newcamd ] ECM -> test (OK) [CAID 0000] [Prov 00000000] [SID 000B]
[ 22:00:30 ] [ Newcamd ] ECM -> test (OK) [CAID 0000] [Prov 00000000] [SID 000B]
[ 22:00:41 ] [ Loader ] Reinit card with caid 0B00
[ 22:00:59 ] [ Newcamd:12000 ] User test logout
[ 22:00:59 ] [ Newcamd:12000 ] User test logged in, client: VDR-SC
[ 22:01:19 ] [ Newcamd:12000 ] User test logout
[ 22:01:19 ] [ Newcamd:12000 ] User test logged in, client: VDR-SC

Dit is mijn newcs configuratie.


<?xml version="1.0"?>
<newCSconfig>

<globals>
<listening-ip>192.168.1.31</listening-ip>
</globals>

<readers name="Card Readers">
<device>
<name>reader1</name>
<enabled>yes</enabled>
<type>phoenix</type>
<node>/dev/ttyUSB0</node>
<mhz>358</mhz>
<reset>normal</reset>
<parity>even</parity>
<export>yes</export>
<blocksa>no</blocksa>
<blockua>no</blockua>
<blockga>no</blockga>
<blockc0>Yes</blockc0>
<rate>0</rate>
<au>yes</au>
<export>Yes</export>
<pincode>0000</pincode>
<Seca-PPV>no</Seca-PPV>
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<priority>round</priority>
<autosid>yes</autosid>
<newcamd_port>12000</newcamd_port>
</device>
</readers>

ter info,
dit heb ik en werkt goed:

<readers name="Standard Phoenix on PC">
<device>
<name>kaartnaam</name>
<type>phoenix</type>
<mhz>357</mhz>
<node>/dev/ttyUSB0</node>
<parity>even</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<blockC0>Yes</blockC0>
<carddetect>yes</carddetect>
<newcamd_port>12000</newcamd_port>
<autosid>Yes</autosid>
<pincode></pincode>
<priority>round</priority>
</device>
</readers>

Thanks Its_Johan,

Toen ik het stuk van jou copieerde liep ik ineens tegen een andere foutmelding aan
[ Newcamd:12000 ] Connection from test to not-ready server!

Ik heb toen een aantal opties weggehaald bij het stukje newcamd-server en het draait nu wel. So far so good maar de duurtest zal het uitwijzen. Bedankt iig!

Groet

Maarten

Na een half uur toch weer een reinit card en toen was het weer afgelopen. Ik word er helemaal gefrustreerd van.

[ 14:24:20 ] [ Newcamd ] ECM -> test (OK) 0B00 0000 000B
[ 14:24:31 ] [ Newcamd ] ECM -> test (OK) 0B00 0000 000B
[ 14:24:40 ] [ Newcamd ] ECM -> test (OK) 0B00 0000 000B
[ 14:24:51 ] [ Loader ] Reinit card with caid 0B00
[ 14:25:10 ] [ Newcamd:12000 ] User test logout

Zou je je hele newcs.xml eens willen publiceren (zonder de account gegevens natuurlijk) ?