Gast Geplaatst: 29 juni 2005 Geplaatst: 29 juni 2005 Ik probeer de software met Autoarioner loader te programmeren, maar dat lukt me niet. Wat doe ik verkeerd? Heeft iemand hier ervaring mee? Alvast bedankt ahyosra@wanadoo.nl
jotronix Geplaatst: 29 juni 2005 Geplaatst: 29 juni 2005 Als je even uitlegt wat je zoal al gedaan hebt en bv. hoe ?? , dan kunnen ze jou hier mischien helpen. En met jou vraag (wat doe ik verkeerd? ) dat kunnen wij alleen maar raden. Ik raad je aan ... <img src="/forums/images/graemlins/lezen.gif" alt="" /> <img src="/forums/images/graemlins/loep.gif" alt="" /> <img src="/forums/images/graemlins/lezen.gif" alt="" /> sucses trouwens welkom op het forum.
THE SPECIALIST Geplaatst: 29 juni 2005 Geplaatst: 29 juni 2005 ik heb je de nieuwste emu firmware gestuurd.groetjes uit dordrecht.met alles erop en er aan arioner.gasoline enzv.
Gast Geplaatst: 30 juni 2005 Geplaatst: 30 juni 2005 ik heb geprobeerd maar lukt het niet de kabel is goede ik heb getest meet Echostar mar ik heb per ongeluk de emu verwijdert van dtm box ik heb fabriek instellingen,maar nog steeds niet Wie wil mij stap voor stap even uitleggen hoe Alvast bedankt
CrazyMotha Geplaatst: 30 juni 2005 Geplaatst: 30 juni 2005 Stekker uit het stopcontact halen. Autoarioner op starten en juiste compoort selecteren. Gewenste software selecteren. Stekker in stopcontact stoppen. Als er goed contact is zal de compoort in het venster de volgende kleuren weergeven: STATUS: GRAY - port not exist RED - port is busy PINK - sending data YELLOW - listening confirmation GREEN - port ready to use BLUE - error - close all application and try again Progress bar: Blue - load status Red - estimate flash status Is het de eerste keer dat je het programma gebruikt, laat dan eerst even de header selecteren d.m.v.: For new tuner use key:74620 in standby for detect header. Verder nog wat tips en verborgen functies: Hidden Function Codes ________________________________________ The list of codes to activate hidden functions in Arion based receivers. For f/w with EMU function to activate it: 1. Go to menu. By pressing menu on your remote 2. Key in : 19370 3. Key in pin: 2486 Now in menu – games, you shall see emu-keys section, should you wish to alter the keys manually, you need to enter pin 0000. If you forgot the pin you had entered, press 0786 to reset it and enter menu or blocked channels. Other Codes to be entered when tuner is in stand by mode. 42114802500 – Full information about your tuner (h/w & f/w) 24680 – Uploading keys (irk) or channels list to the receiver. 74621 – Downloading channels list from the receiver. 74623 – Downloading full set of keys from the receiver. 74620 – Downloading f/w from the receiver (AUC_HEDIT). 14802 – Downloading boot from the receiver (AUC_HEDIT) 14809 – Downloading full f/w with boot from the receiver (AUC_HEDIT) – you get “universal” f/w this way. Test codes: 42125 42126 42127 __________________________________________________ To connect your PC to the receiver, you'll need null modem RS 232 9-pin cable: 1+6---->4 2------>3 3------>2 4---->1+6 5------>5 7------>8 8------>7 __________________________________________________ How to receive the STB Data from the STB to PC. NOTE: Receive indicates that transfers the existing data (STB Data) from the STB to your PC; whereas, Send indicates that transfers the added or modified data from PC to the STB). 1. Choose the "Receive" menu from Main Menu or Toolbar. 2. Turn on the main power of STB. 3. Press special key-code "74621" in the STB stanby mode. 4. The STB Data will be transferred automatically, with a window indicating the process status. (If you wish to abort receiving process click 'CANCEL' button.) 5. When finished the receiving process, click the 'OK' button and then an active window will appear your received data. Please save the data with specific name using "Save As" menu. How to send the STB Data from PC to STB. 1. Choose the "Send" menu from Main Menu or Toolbar. 2. Turn on(reboot) the main power of STB. 3. The STB Data will be transferred automatically, with a window indicating the process status. If you wish to abort sending process click 'CANCEL' button. AF1018SE, AF2018SE, AF3018SE, AF4018SE AF5018CI s/w upgrade Upgrade procedure 1. Power off receiver. 2. Connect PC and receiver using a serial cable. Receiver should be power-off state. 3. Execute "ARIONER.EXE" First, Select proper PORT. ex) COM1 or COM2 4. Click the "Open" button and select "ADA2030SE.auc". Click the "Send program to IRD" button. Then, typically "Last status" shows message of "Waiting connect request ack". Now PC are ready to transfer. 5. Power on receiver upgrade process will be automatically done in a few seconds. You can see the progress with PC and/or receiver. NOTE When receiver shows "Saving" message, you have to be very careful. Never power off during this save time. It couldn't reboot and you have to send back the receiver to us. At the end of the process, small message window at PC will appear. Please don't care about the message. Click "OK" button to clear the message. Receiver reboot automatically. Check front display of receiver. If it shows "----" or any channel number "xxxx", then successful. AF8018UCI s/w upgrade 1. Press “24680” in standby Mode 2. You can see “AIT” on the front panel 3. Open the file “***.U01” by using PSLoader 4. Then you can see POPUP menu to ask to open another file 5. Then, select the file “***.U02” 6. The selection order of files must follow up. 7. S/W upgrade will be done automatically. 8. After completion of upgrade, the receiver will be rebooting automatically. I'm not a complete idiot, some parts are missing. Dreambox 8000 HD - Vu Duo
Gast Geplaatst: 30 juni 2005 Geplaatst: 30 juni 2005 even uitlegt wat de software is hardware version: ps-1900 softwar version: $DHMA5172S190CIn database version :00000209 boot version: 0015.1
Gast Geplaatst: 1 juli 2005 Geplaatst: 1 juli 2005 hij is van een vriend misschien heeft hij wat fout gedaan ik ben de hele tijd bezig geweest maarlukt het niet ik wil graag weten of dit een DTM BOX 2004 is hardware version ps-1900 softwar version $DHMA5172S190CIn database version 00000209 boot version 0015.1
Gast Geplaatst: 1 juli 2005 Geplaatst: 1 juli 2005 ik heb een Firmware van powersky ps1900ci Update26-06-05 een het is goed gegaan want met dtm box firmware is het niet gelukt maar nu ik kan geen gecodeerde kanalen zien wat kan ik nog meer doen
mteam Geplaatst: 1 juli 2005 Geplaatst: 1 juli 2005 Druk menu - daarna op de afstandsbediening code 19370 en daarna in de 4 vakjes 2486 Dan is de emu pas geactiveerd. Groetjes Danny
Gast Geplaatst: 15 maart 2006 Geplaatst: 15 maart 2006 hallo ik ben nieuw hier en wou vragen of er iemand mij kan helpen met de software en patch van een dtm box 2004 ik zou het echt op prijs stellen mijn email is suppafly1970@hotmail.com <img src="/forums/images/graemlins/xyxthumbs.gif" alt="" />
jotronix Geplaatst: 15 maart 2006 Geplaatst: 15 maart 2006 PM = persenal mail. Zie links boven op deze pagina onder de tab:mesage board en dan ff op mijn profiel klikken , dan kan je de pm's lezen. sucses
Gast Geplaatst: 15 maart 2006 Geplaatst: 15 maart 2006 ok heb begrepen maar ik heb noch niets om verder te kunnen doen please help me zit vast,geblockeert en nog zo van die lastige dingen je weet wel
Aanbevolen berichten
Maak een account aan of log in om te reageren
Je moet een lid zijn om een reactie te kunnen achterlaten
Account aanmaken
Registreer voor een nieuwe account in onze community. Het is erg gemakkelijk!
Registreer een nieuwe accountInloggen
Heb je reeds een account? Log hier in.
Nu inloggen