-
Items
391 -
Registratiedatum
-
Laatst bezocht
Inhoudstype
Profielen
Forums
Store
Berichten die geplaatst zijn door Freeangel
-
-
Ik begrijp dat je de Free-x-kaart gewoon lopende krijgt via de interne cardreader.
Maar ik heb nu nog een vraag. Gebruik je alle twee de cardreaders en zo ja kun je dan met hetzelfde emu allebei de kaarten benaderen????
Ik heb zelf namelijk een Canal+ kaart en deze zit altijd in de cardreader. Echter gisteren heb ik ff een funkaart gemaakt met de files voor SCT en EXTASI en deze in het bovenste slot gedaan.
Dan werkt het dus niet voor allebei tegelijk.
Als de C+ kaart en de fun erin zitten dan draait alleen de C+ kaart.
Als de fun alleen erin zit doet hij het wel.
Dus zeer lastig als je wilt zappen want dan moet je elke keer ff rebooten.
-
Bij mij wordt de kaart geupdate via SCAM_CS en met deze EMU zijn ook de opnames perfect <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" />
-
Citaat:Hier al eens gekeken ?
Nu wel. Bedankt <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" /> -
<img src="/ubbthreads/images/graemlins/anoniem.gif" alt="" /> weer wat geleerd.
Echter er moet een lijst zijn met goedgekeurde USB-sticks, zit al een poos te zoeken maar kan hem niet vinden.
Iemand die hem nog heeft liggen???
-
Als je een usb stick gebruikt kan dan de klep van de DB7000S nog dicht of moet die open blijven staan???
-
Kan iemand me helpen want ik kom er echt niet uit, hoewel ik dit draadje al 100 keer heb gelezen!!!!
Ik draai de PLI van 2410 op een dreambox 7000S
Zo ziet mijn cardserv.cfg eruit;
CLIENT_CONNECT_TIMEOUT = 20
#
# debug options (A) - show network and card init, ecm and emm packages
# DEBUG_INIT = no
# DEBUG_NET = no
# DEBUG_ECM = no
# DEBUG_EMM = no
#
# Serial Port (Phoenix/Multicam) (Section divider)
# The first SERIAL_PORT options ends the global section
# On Dreambox SERIAL_PORT = 0 is the upper card slot,
# SERIAL_PORT = 1 is the lower card slot and 2 is the
# actual serial port
# SERIAL_PORT = <no> begins a single card's local section
# SERIAL_PORT = 0
#
# Serial Port (sc8in1) (section devider)
# SERIAL_PORT = <no> sc8in1 begins a sc8in1 description
# SC8IN1_SLOT must follow immediately to start a local section
# SERIAL_PORT = 1 sc8in1
#
# sc8in1 slot (sc8in1 sub section divider)
# valid slots are 0-7, 0 being the left most connector on the sc8in1
# SC8IN1_SLOT = 1
#
# Parity - serial communication parameter for the smartcard (L)
# The default is on, which is correct for all cards except Irdeto
# This is for reading the ATR only, after the ATR has been recognized by
# cardserver, it automatically switches to the correct communication parameters
# Some Irdeto cards work with PARITY = on also, some need PARTIY = off, so just
# test it. Dreambox cardreaders don't need this option, so it will be rejected
# for SERIAL_PORT = 0, 1 on Dreambox
# PARITY = on
#
# CARD_DETECT_BIT (L)
# different Phoenix readers sometimes use different serial lines to detect an
# inserted card, here you can specify, which line cardserver should use for a
# particular card. Possible values are CTS, DCD and DSR
# Default is CTS for sc8in1 and dbox2 serport 1, DCD otherwise
# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)
# CARD_DETECT_BIT = DCD
#
# Baudrate (L) (DBOX2 version ONLY!)
# Baudrate selection for the dbox2 server. Allows to run 6 MHz with
# 3.579 MHz crystal and (theoretically) the other way around.
# Keep in mind, running anything but Irdeto cards at 6 MHz is overclocking!!!
# Irdeto card at 3.57 MHz: BAUDRATE = 5727
# other card at 6 MHz: BAUDRATE = 16128
# Default is 9622, which is correct for all except Irdeto cards at 3.579 MHz
# 3579545 Hz / 372 = 9622 bit/s (see iso 7816)
# This option will be rejected on Dreambox and I386
# BAUDRATE = 9622
#
# TCP port (L) - the port listening for connections for a particular card
# TCP_PORT = 2000
#
# EMM options - block EMM-U, EMM-G or EMM-S (A)
# EMM-G = no
# EMM-S = no
# EMM-U = no
#
# For iso cardreaders that close the card switch contact instead of opening it,
# when a card is inserted (L)
# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)
# CARD_DETECT_INVERT = yes
#
# Special features (only for some cards) (L)
# SPECIAL_FEATURES = no
#
# Exclude services - Some providers offer a PPV preview by allowing a card
# to decrypt a certain number of ECMs of each PPV event before it has to be
# bought. Sharing such a card with other people allows them to "steal" this
# PPV preview. With this option, you can tell cardserver to not ask the card
# to decrypt ECMs for certain services, except if user 1 (the EMM user) asks
# for them. Each blocked service has to be listed with its service id.
# A service id is a 16-bit number and has to be given in hex.
# camdcmd offers a possibility to change the list of blocked services without
# restarting cardserver (if for example you have bought a PPV event and now
# want to share it).
#
# Block single service
# EXCLUDE_SERVICE = 13a9
# You can also block a range of service ids, the following blocks all services
# from 02be to 02c8
# EXCLUDE_SERVICE_MULTIPLE = 02be:02c8
#
# Example: you should change at least the DESKEY !!
#
DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
SERVER_NAME = cardserver
DEBUG_PORT = 14000
ADMIN_PORT = 14001
ENTITLEMENT_PORT = 14002
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
# Below here you can define users
USER = root dreambox lan
#
# upper card slot
#
SERIAL_PORT = 0
TCP_PORT = 10000
EMM-G = yes
EMM-S = yes
EMM-U = yes
SPECIAL_FEATURES = yes
#
# lower card slot
#
SERIAL_PORT = 1
TCP_PORT = 10001
EMM-G = yes
EMM-S = yes
EMM-U = yes
SPECIAL_FEATURES = yes
#
En zo ziet mijn newcamd.conf eruit;
# /var/tuxbox/config/newcamd.conf
#
# newcamd mandatory settings
#
# What Demux API is used? (1 = very old, 2 = rel (Dreambox), 3 = head (VDR))
DEMUX_API = 2
# on PPC version: What Box is used? Valid options are DBOX2, DM7000 and DM5600
# on I386 version this parameter is ignored
BOX_TYPE = DM7000
# Which device for writing control words should be used?
# Valid options are CA, SDEV or GTX
# (SDEV and GTX = /proc/bus/gtx, CA = /dev/caX or /dev/dvb/card0/caX)
CONTROL_WORD_DEVICE = CA
# What CA0 API is used?
# 3 for recent DVB-S driver or recent Dreambox drivers (dream.o from 1.07.3)
# also for ca1 use on dbox2
# 2 for older Dreambox driver (ca.o or dream.o up to 1.07.2)
# no effect on PPC version if CONTROL_WORD_DEVICE = GTX or SDEV
CA_API = 3
# output control words to /proc/bus/gtx in 16 byte or 4096 byte packets
# no effect on I386 version or on PPC version, if BOX_TYPE = DREAMBOX
GTX_OUTPUT_MODE = 4096
# This is important for channels which frequently change between free and
# encrypted broadcasts. The change will be reflected in the PMT. If you
# don't want your picture to stop when the channel goes from free access
# mode to encrypted mode, either your zapper (zapit/Enigma) or newcamd
# itself has to keep track of PMT changes. Recent Enigma versions do this,
# so you can set PMT_UPDATE_WATCH to no. Recent Zapit versions also have
# this option, but it is not compiled by default. So when using Zapit
# without PMT updates, you need to enable newcamd to monitor the PMT
# (PMT_UPDATE_WATCH = yes). Having both zapper and newcamd monitor
# the PMT at the same time, can lead to all kind of instabilities and
# should therefore by avoided, although it might seem to work at first.
PMT_UPDATE_WATCH = no
# Use emulator?
EMU = yes
# if both control word server and emulator keys are available for the
# channel, which method should be tried first?
PREFER_EMU = no
# deactivates the dbox2 Betacrypt CAM
# this has to be set to yes on Dreambox
DISABLE_CAM = yes
# use dbox2 Betacrypt CAM for caids 06, 17 or both (00)?
CAM_CASYS = 17
# Autoupdate for Emu and Control Word Servers
# AU is always yes if there are Betacrypt UDS control word server
# connected to newcamd
AU = no
#
# newcamd debug options
#
# dumps all ca systems used by a channel on the console
SHOW_ALL_CA_SYSTEMS = yes
# On Screen Display, neutrino, enigma or none
OSD = none
# print debug messages about ECM handling
DEBUG_ECM = no
# print debug messages about EMM handling
DEBUG_EMM = no
# print debug messages about Control Word Server (CWS)
DEBUG_CWS = no
# print debug messages about dbox2 CAM (cam-alpha.bin)
DEBUG_CAM = no
# print command message to/from dbox2 CAM as hex strings
DEBUG_CAM_HEX = no
# print all plain control words used
SHOW_CW = no
# hex dump of entire PAT
SHOW_PAT = no
# hex dump of entire PMT
SHOW_PMT = no
# hex dump of entire ECM
SHOW_ECM = no
# hex dump of entire CAT
SHOW_CAT = no
# hex dump of entire EMM (AU)
SHOW_EMM = no
# show network ECM messages being sent and received from/to the cardservers
SHOW_CWS_ECM = no
# show network EMM messages being sent and received from/to the cardservers
SHOW_CWS_EMM = no
# hex dump of EMMs with wrong signature
EMM_REPORT_WRONG_SIG = no
# delay between channel zap and appearance of the OSD
OSD_WAIT_TIME = 500
#
# newcamd optional settings
#
# Delay between reception of new control word and writing them into
# the CSA registers
# this is a default, can be changed for each individual key in keylist
DEFAULT_CW_DELAY = 500
# reload config on every channel zap
RELOAD_CONFIG_ON_ZAP = yes
# reload keylist on every channel zap
RELOAD_KEYLIST_ON_ZAP = yes
#
# newcamd mandatory settings for control word servers (cws)
#
# Cardserver list
#
# <hostname> <port> <username> <password> <14 byte triple-des key in hex> <lan/wan> <cardserver name>
#
# wan connections will be dropped and rebuild if newcamd is told so by camdcmd
# (see admin options)
#
# hostname = uds to use betad, port is the serial port in that case
#
# CWS = uds 1 dummy dummy
# this example works with the example cardserv.cfg!!!
CWS = 127.0.0.1 10000 root dreambox 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
CWS = 127.0.0.1 10001 root dreambox 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
#
# newcamd optional settings for using control word servers (cws)
#
# Timeout for cardserver login in 100ms
CWS_CONNECT_TIMEOUT = 30
# Port to listen for incoming cardserver connections (reverse login)
# and/or admin connections
CWS_INCOMING_PORT = 12000
# Port to get a list of all connected cardservers, just telnet to it
CWS_DEBUG_PORT = 12001
#
# newcamd admin control options
# (incoming port is the same as CWS_INCOMING_PORT)
#
# <password> <14 byte des key>
#
ADMIN_PASSWORD = admin 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Hoewel ik denk dat alles zo goed staat krijg ik GEEN beeld op mijn canal+ card!!!
Iemand een idee wat er fout gaat????
-
Als je dan voorbij de laatste zender in een bouquet gaat gaat hij naar het VOLGENDE bouquet als je dit aanvinkt.
Als je dit niet aanvinkt dan gaat hij weer naar de eerste van HETZELFDE bouquet.
-
@ pli en tcc
Ik krijg het automatisch ophalen van de epg nog steeds niet helemaal werkend.
Als ik de commando's uit het bestand goepg handmatig invoer in telnet dan werkt dit perfect.
Als ik echter /var/bin/goepg ingeef, krijg ik de volgende melding -sh: /var/bin/goepg: not found en word het bestand dus NIET uitgevoerd.
Wat kan hier aan de hand zijn????
Alvast bedankt voor de moeite
-
Citaat:Wat nog nog vergeten waren te melden is dat de MediaHighway EPG elke nacht om 06:00 uur wordt binnengehaald.
Wordt je 's ochtends wakker staat de Dreambox al op het journaal (Nederland 2) :-) (note: Teministe als Nederland 2 op 2 hebt staan...)
Zorg ervoor dat in de "Service to run" een vinkje bij "start Crond" staat.
Met dank aan tCC voor het uitzoeken.
Groeten,
Rick
Ik heb hem inmiddels in de installer zien staan echter alleen voor de USB en NIET voor de HDD.
Komt deze er ook nog of werkt de USB versie ook voor de HDD??? -
Weet er iemand of de orginele free-X-tv kaart ook werkt in de interne cardreader??? Zo ja welke emu gebruik je hiervoor??
Kan het zelf niet testen aangezien ik niet zo'n kaart heb maar wil er wel 1 aanschaffen.
-
Dit is voor een paar dagen, het ligt eraan hoe laat op de dag je de EPG gegevens ophaalt.
Ja, dat was op de PLI 3009 ook al. <img src="/ubbthreads/images/graemlins/grin.gif" alt="" />
-
Ik ben bij mijn vriend wwar ik de boel moet installeren.
Ik sluit dezelfde kabel aan die ik thuis gebruik en start dreamup voor de DM5620S op en................tot mijn verbazing krijg ik gewoon connectie <img src="/ubbthreads/images/graemlins/confused.gif" alt="" />
Ik snel de PLI erop gezet en draaien die handel <img src="/ubbthreads/images/graemlins/grin.gif" alt="" /> <img src="/ubbthreads/images/graemlins/biggthumpup.gif" alt="" />
Wat een rare dingen die PC's <img src="/ubbthreads/images/graemlins/cool.gif" alt="" />
-
Ik word hier helemaal gek van!!!!!!!!!!!
Kan nieuwe DM5620S, zo uit de doos niet connecten.
Via ftp wel maar zoals op dit board al beschreven kan je geen bestanden verzenden met de orginele versie.
Via de seriele poort ook geen connectie!!!
Via hyperterminal volgens mij wel connectie, ik krijg geen foutmeldingen maar wel allemaal gekke tekens op een regel die langzaam meer worden.
De kabel en PC zijn zeker goed want ik kan zonder probleem connectie maken met mijn DM7000S
Heeft iemand nog tips of wordt het een retourtje dealer????
Alvast bedankt voor jullie hulp.
-
Hallo allemaal,
Kun je de erase image van een DM7000 ook voor de DM5620S gebruiken???
-
Na enig stoeien met de newcamd.config ben ik eruit.
Volgens mij zat het probleem in de regel met CA_API = 2 deze moet de waarde 3 hebben. <img src="/ubbthreads/images/graemlins/smile.gif" alt="" />
-
Volgens mij komt dat door de drivers van Dream. Als je SCAM als emu neemt zal veel minder of niet meer voorkomen
-
Bij gebruik bovenste SCART , schakert TV automatisch over op goede EXT uitgang.
Bij gebruik onderste SCART, moet je handmatig TV op goede EXT uitgang zetten
-
Aangezien volgens de experts de CS van Ronaldd een eind uitgeevolueerd is ben ik op zoek naar een andere oplossing.
Ik probeer nu mijn C+ card te laten draaien via de NEWCAMD en NEWCAMDserver echter ik krijg maar geen beeld.
Misschien kan iemand me hier helpen???
Mijn newcamd.conf ziet er zo uit:
# /var/tuxbox/config/newcamd.conf
#
# newcamd mandatory settings
#
# What Demux API is used? (1 = very old, 2 = rel (Dreambox), 3 = head (VDR))
DEMUX_API = 2
# on PPC version: What Box is used? Valid options are DBOX2, DM7000 and DM5600
# on I386 version this parameter is ignored
BOX_TYPE = DM7000
# Which device for writing control words should be used?
# Valid options are CA, SDEV or GTX
# (SDEV and GTX = /proc/bus/gtx, CA = /dev/caX or /dev/dvb/card0/caX)
CONTROL_WORD_DEVICE = CA
# What CA0 API is used?
# 3 for recent DVB-S driver or recent Dreambox drivers (dream.o from 1.07.3)
# also for ca1 use on dbox2
# 2 for older Dreambox driver (ca.o or dream.o up to 1.07.2)
# no effect on PPC version if CONTROL_WORD_DEVICE = GTX or SDEV
CA_API = 2
# output control words to /proc/bus/gtx in 16 byte or 4096 byte packets
# no effect on I386 version or on PPC version, if BOX_TYPE = DREAMBOX
GTX_OUTPUT_MODE = 4096
# This is important for channels which frequently change between free and
# encrypted broadcasts. The change will be reflected in the PMT. If you
# don't want your picture to stop when the channel goes from free access
# mode to encrypted mode, either your zapper (zapit/Enigma) or newcamd
# itself has to keep track of PMT changes. Recent Enigma versions do this,
# so you can set PMT_UPDATE_WATCH to no. Recent Zapit versions also have
# this option, but it is not compiled by default. So when using Zapit
# without PMT updates, you need to enable newcamd to monitor the PMT
# (PMT_UPDATE_WATCH = yes). Having both zapper and newcamd monitor
# the PMT at the same time, can lead to all kind of instabilities and
# should therefore by avoided, although it might seem to work at first.
PMT_UPDATE_WATCH = no
# Use emulator?
EMU = yes
# if both control word server and emulator keys are available for the
# channel, which method should be tried first?
PREFER_EMU = yes
# deactivates the dbox2 Betacrypt CAM
# this has to be set to yes on Dreambox
DISABLE_CAM = yes
# use dbox2 Betacrypt CAM for caids 06, 17 or both (00)?
CAM_CASYS = 17
# Autoupdate for Emu and Control Word Servers
# AU is always yes if there are Betacrypt UDS control word server
# connected to newcamd
AU = no
#
# newcamd debug options
#
# dumps all ca systems used by a channel on the console
SHOW_ALL_CA_SYSTEMS = yes
# On Screen Display, neutrino, enigma or none
OSD = none
# print debug messages about ECM handling
DEBUG_ECM = no
# print debug messages about EMM handling
DEBUG_EMM = no
# print debug messages about Control Word Server (CWS)
DEBUG_CWS = no
# print debug messages about dbox2 CAM (cam-alpha.bin)
DEBUG_CAM = no
# print command message to/from dbox2 CAM as hex strings
DEBUG_CAM_HEX = no
# print all plain control words used
SHOW_CW = no
# hex dump of entire PAT
SHOW_PAT = no
# hex dump of entire PMT
SHOW_PMT = no
# hex dump of entire ECM
SHOW_ECM = no
# hex dump of entire CAT
SHOW_CAT = no
# hex dump of entire EMM (AU)
SHOW_EMM = no
# show network ECM messages being sent and received from/to the cardservers
SHOW_CWS_ECM = no
# show network EMM messages being sent and received from/to the cardservers
SHOW_CWS_EMM = no
# hex dump of EMMs with wrong signature
EMM_REPORT_WRONG_SIG = no
# delay between channel zap and appearance of the OSD
OSD_WAIT_TIME = 500
#
# newcamd optional settings
#
# Delay between reception of new control word and writing them into
# the CSA registers
# this is a default, can be changed for each individual key in keylist
DEFAULT_CW_DELAY = 500
# reload config on every channel zap
RELOAD_CONFIG_ON_ZAP = yes
# reload keylist on every channel zap
RELOAD_KEYLIST_ON_ZAP = yes
#
# newcamd mandatory settings for control word servers (cws)
#
# Cardserver list
#
# <hostname> <port> <username> <password> <14 byte triple-des key in hex> <lan/wan> <cardserver name>
#
# wan connections will be dropped and rebuild if newcamd is told so by camdcmd
# (see admin options)
#
# hostname = uds to use betad, port is the serial port in that case
#
# CWS = uds 1 dummy dummy
# this example works with the example cardserv.cfg!!!
CWS = 127.0.0.1 10000 root dreambox 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
#
# newcamd optional settings for using control word servers (cws)
#
# Timeout for cardserver login in 100ms
CWS_CONNECT_TIMEOUT = 20
# Port to listen for incoming cardserver connections (reverse login)
# and/or admin connections
CWS_INCOMING_PORT = 12000
# Port to get a list of all connected cardservers, just telnet to it
CWS_DEBUG_PORT = 12001
#
# newcamd admin control options
# (incoming port is the same as CWS_INCOMING_PORT)
#
# <password> <14 byte des key>
#
ADMIN_PASSWORD = admin 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Het enige wat anders is is mijn password om in te loggen ,moet dit dan ook in regel 111 veranderd worden???
De newcamd.cfg heb ik ongemoeid gelaten en de NEWCAMDcardserver is gestart in Services to Run menu.
-
Citaat:Hoi,
M'n eerste image voor de DM5620 is gereed.
Hierin vind je terug Newcamd + cardserver 5.17, scam 3108 en de ronaldd cardserver + cs_client.
Hoe kan je de CS client activeren of selecteren????
Hij staat niet tussen de emu's (geen SCAM-CS of NEWCAMD_CS) -
Niemand die hier een oplossing voor weet???
-
Ja, dat kan werkt gewoon in de onderste (bovenste ook geloof ik) cardreader dan emu NEWCAMD of SCAM gebruiken.
Er zullen misschien nog wel meer emu's zijn waar hij mee werkt
-
Hallo allemaal,
Een kennis van mij vroeg of ik een andere mage wilde flashen in zijn DM5620S.
Aangezien ik zelf een DM7000 heb en dit regelmatig doe, wilde ik hem wel ´even´ helpen.
Echter tot mijn verbasing kon ik geen connectie krijgen met de Dreambox, terwijl ik zeker weet dat mijn kabel enz. goed is omdat ik dit dus regelmatig met mijn eigen Dreambox doe.
Hij blijft hangen bij ´uploading´ en de blauwe balk wordt slechts een paar mm blauw.
Heeft iemand hier ook ervaring mee of een oplossing voor???
Alvast bedankt voor het meedenken.
-
Klopt het ophalen van de gegevens werkt gewoon niet altijd.
Wel als je handmatig doet, zie de tread van PLI 7000 image.
-
(DM7000S) formateren USB-stick onder PLI 2410
in Dreambox
Geplaatst:
Hallo,
Ik heb vandaag mijn USB-stick binnen gekregen en wil hem nu gaan gebruiken om de /var directory van PLI 2410 op te zetten.
Echter in de "vroegere"images was er een optie om de USB-stick te formateren maar ik kan hem in deze image niet vinden.
Is het nog nodig om de USB-stick te formateren voor gebruik of gebeurt dit automatisch als je er iets wilt op opslaan??
Kan iemand me wat meer duidelijkheid verschaffen aub??