Jump to content
Sign in to follow this  
RikH

[Pioneer] VERSIE 3.0 voor de Pioneer 15XX

Recommended Posts

@Spirit Rules,

 

Ten eerste weer complimenten voor de nieuwe versie. Kun je mij uitleggen hoe het dumpen van een mpeg sessie werkt? En betekent dit dat we stukken kunnen opnemen op de computer in mpeg formaat? En wat ik me ook nog afvroeg is er al nieuws over Sky Italia?

 

Rik

Share this post


Link to post
Share on other sites

Citaat:
Kun je mij uitleggen hoe het dumpen van een mpeg sessie werkt?

Lees de read-me file die erbijzit

 

Citaat:
En wat ik me ook nog afvroeg is er al nieuws over Sky Italia?

Alleen met org.kaart

Share this post


Link to post
Share on other sites

Oke dan zou dit het moeten zijn:

 

-Dumpen van mpeg sektie mbv mediacom 2.1

 

Dumping of MPEG sections via RS232 added.

Dev_MCOM serves this on receiver side. I haven't any info about this device except one i got from disassembled pioneer's firmware.

So a lot of thins is still unknown :-| Some arguments of MCOM related functions may be manually corrected in MediaCom.INI file (read comments within this file for details).

 

Operation.

Press Load PID button. On popped-up dialog (Table Load options) enter the PID which you want to log and ajust hard filter value and mask( if necessary. In some cases you may fill all mask fields by 00 so the filter will be disabled and each section coming with this PID will be uploaded to host).

Don't forget to set a proper time-out, e.g. seca provis send EMM very rarely (about one packet per hour), while viac EMMs are arriving quite often.

Check the checkbox Continuos load and then OK button. At last, choose the file where data would be dumped.

 

Note, log file length is limited by 100kB max. However, you may abort dumping anytime by pressing of Stop button.

Some mpeg sections may be missed due to high intensivity of stream, i was tested the Load PID on viasat and TPS transponders for logging of EMM stream.

About 3-5% of EMMs was missed on TPS and 0% on viasat.

You may play with MCOM parameters (within ini file) and hard filter value/mask to optimize the performance and arrived/missed ratio.

 

Warning !!! No sanity check is made during dumping process. ALL incoming data are stored in the log file.

In some cases MHW may report about receive/transmit/memory errors and error messages will be written into log file as well as PID data.

 

Known bug: stopping of dump doesn't cause an immediate abort of transmittion. MCOM device continues to send data to host until all previously received data will be sent out.

So after pressing of Stop you see a garbage in trace window. Don't care <img src="/ubbthreads/images/graemlins/smile.gif" alt="" /> Probably it may be fixed in both MHW and MediaCom in future, i haven't a time for it now...

 

Greate thanks Ldnlp for his work with firmware, help and good advices <img src="/ubbthreads/images/graemlins/smile.gif" alt="" />

 

Nou alle stappen gevolgt maar helaas geen resultaat.

Share this post


Link to post
Share on other sites

Kan iemand met een 15xx nu wel of niet freex tv ontvangen?

Ik hoor hier niets over!!!!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...

Important Information

Onze Terms of Use en Privacy Policy