digisat pro lcd accu nog maar 1 signaal meter.

[puk5600]

had vandaag even niets te doen op het dak dus ging ik het menu eens doorspitten. maar eerst had ik mooi twee meters in mijn scherm nu nog maar een. en ik kan ook niet meer in het menu vinden wat ik moet verzetten. <img src="/forums/images/graemlins/xyxthumbs.gif" alt="" /> <img src="/forums/images/graemlins/xyxthumbs.gif" alt="" />

[Sjaak(k)]

Met de 2 gele knoppen kun je kiezen voor 1 of 2 displays, ook kun je de pieper aan of uitzetten per display met de bijbehorende gele knop <img src="/forums/images/graemlins/xyxthumbs.gif" alt="" />

[puk5600]

pieper zet ik aan met het onderste knopje maar de tweede meter komt niet ook niet met het bovenste knopje.

[Sjaak(k)]

RTFM <img src="/forums/images/graemlins/blush.gif" alt="" />

DIGISAT PRO Owners Manual How to connect: * Start by connecting the LNB(s). Connect the input LNB 1, LNB 2 or both.*Power is connected via the “Receiver” F-input or by the DC-plug, 12-18 V. Turn On/Off: *Turn on by pressing down the red “On/Menu”-button. The unit starts in the dual-measuring mode, showing two thermometer-scales. *Turn the unit Off by pressing down the yellow “Off/Down”-button for a couple of seconds.Operation: * Use the yellow “up” button to select the wanted inputs. One push selects the LNB 1 input, another push switches to the LNB 2 input and a third push gets the unit back to dual-measuring mode (showing the signal-strength of two LNBs at the same time). * Use the yellow “down/off” button to select and hear audio (pitch-tone) from one of the connected LNBs. One push selects the LNB 1 input, another push switches to the LNB 2 input and a third push gets the unit back to the no-sound mode. Menu system: The following menu is shown on the LCD when pressing down the red “On/Menu”-button: SIGNAL VIEW 22 kHz MODE RECEIVER VIEW MOTOR CONTROL DiSEqC CONTROL SETUPUse the yellow buttons to scroll up and down in the menu system. Use the red button to enable the selected function. Below follows a description of the different functions: SIGNAL VIEWGets the unit back into measuring mode. The unit measure signal strength from one or two LNBs. Individually orat the same time.The higher values, the better signal.22 kHz MODE The DIGISAT PRO can transmit 22 kHz to control switches/LNBs. In this mode the 22 kHz can be set On,Off orToggle. The unit switches between On/Off by itself in a slow phase in the toggle mode (very useful as some satellites dont have transmissions on both polarities). RECEIVER VIEW Presents the signals coming from the receiver, like:Voltage: Current: 22 kHz: DiSEqC Toneburst: A or B (Off or On) Position + Option: Input 1,2,3,4 (off/off, off/on, on/off, on/on) Switch 1-4Switch 1-4 on or off.

--------------------------------------------------------------------------------

Page 2

MOTOR CONTROL A very useful function today as DiSEqC 1.2 actuators are getting more and more popular. The DIGISAT PRO can control DiSEqC 1.2-, NOKIA SatScan and Triax H/H-actuators The unit runs such an actuator east/west when enabling the DRIVE-function.Signal-strength is also shown in this mode. The LIMITS OFF function disable the factory set limits (east/west) in theactuator. SET EAST LIMIT sets a new east limit. SET WEST LIMIT sets a new west limit. DiSEqC CONTROL The DIGISAT PRO transmits the most common DiSEqC-commands in this mode. Control and test DiSEqC-switches by selecting Input 1-4 (control either a 2-way or a 4-way switch). Check MiniDiSEqC-switches by selecting Toneburst (T-burst) A or B.SETUP The following choices can be made in the SETUP-menu: - ATTEN ON/OFF.If the incoming signal is to strong, (the thermometer-scales shows max and the signal strength value shows 99.9) it can easily be attenuated by enabling this “attenuation”-function. It reduces the incoming signal to a lower level.- SWITCH MODE. The DIGISAT PRO can also be setup and working as a 2-way switch ! Chose between these types:* TB Toneburst- (MiniDiSEqC ) switch* POS DiSEqC “position” switch * OPT DiSEqC “option” switch * SW1 DiSEqC “switch 1” switch * SW2 DISEqC “switch 2” switch * 14/18V14/18 volt switch * 22 KHZ 22 kHz switch - LCD-CONTRAST To adjust the contrast of the LCD; darker or lighter. - AUTO-OFF TIMER Setting the Auto-off of the unit; 1 min, 5 min, 15 min or 30 min. - MAXHOLD On or Off. Indicates the highest measured signal-strength on the thermometer-scales (peak-hold). <img src="/forums/images/graemlins/grin.gif" alt="" />

[puk5600]

dat is het pdfje van digisat. of niet

 

ik heb die namelijk ook al gelezen maar ik krijg het niet gevonden.

[Sjaak(k)]

Als je goed leest moet je diverse keren op de gele up toets drukken <img src="/forums/images/graemlins/blush.gif" alt="" />

Bij mijn zoektocht zag ik overigens ook een Digisat3 pro, ook daar is een pdf van, deze heeft maar één lnb aansluiting <img src="/forums/images/graemlins/confused.gif" alt="" />

[puk5600]

up of down zijn allebij geel. ik heb mijn eigen gek gedrukt maar krijg geen twee meters meer terug.