Ga naar inhoud


Aanbevolen berichten

Geplaatst:

Ik heb voor de lol 's die speciale Kaonbootloader en de aangepaste firmware in een SAB 8010 geladen, inderdaad, emu kan je unlocken en inderdaad, spanje werkt;

irdetokeys van bv ORF zie ik staan, maar N2 keys van D+, waar staan die in die EMU??

 

Overigens staat er op diezelde site ook een Kaonconfigurator, waarmee je kanalen en keys zou kunnen uitlezen, veranderen en terugzetten, maar dat progje zeurt bij mij (W98) over een OCX bestand dat het niet doet; iemand een oplossing?


Geplaatst:

De keys van N2 zitten in de firmware zelf, dus niet in de keys sectie.

Als D+ de keys wisselt, moeten wij firmware wisselen.

Geplaatst:

Volgens een bekend Duits board hoef je niet meer te wachten op nieuwe firmware. Zoek in Google op spinnes board en kijk onder de Kaon sectie. Ik heb het zelf nog niet geprobeerd, maar het ziet er veelbelovend uit!

Geplaatst:

Wil je even in het kort vertellen wat hier staat??? Dat is toch niet verboden.

 

Dank U <img src="/forums/images/graemlins/xyxthumbs.gif" alt="" />

Groetjes

Sunny Sat

Geplaatst:
Citaat:
Volgens een bekend Duits board hoef je niet meer te wachten op nieuwe firmware. Zoek in Google op spinnes board en kijk onder de Kaon sectie. Ik heb het zelf nog niet geprobeerd, maar het ziet er veelbelovend uit!


Nee dat hoef je ook niet want de spaanse emu is voledig AU en ik kan wel die N2 keys aanpassen, het zal wel weer aan die sunny firm liggen die ook niet wil unlocken op bepaalde kaon hardware versies.
Geplaatst:

Babelfish geeft de volgende vertaling:

 

For the Patch we need a MULTI_AES_K*Y PATCHER (it gives on all ULC's), the Prog Picbin172 and Wordpad. As the first we change with Picbin172 our firmware of are in Hex (simply as bin open and as hex store). So that this also folds, the file name of the firmware should be reduced before to a minimum (thus e.g.. "KSC-570_HW12.01.A1...." in "K" rename. After converting we open the new Hexdatei with Wordpad. Now we look for the old Nagra2-K*y over the search function (-- works on searches). We give thus F1.... (to the search not less than six places enter, otherwise gibt's too many hits, to one the correct place found). With the 12.01.A1, SW 0B.00.01 one would find the cookie now under the offset address C7A86 (C7A8 is located in front in the line the 6 is the place, in which the K*y begins. One can note naturally also as offset C7A80, then one regains the cookie in the Patcher exactly the same. There is no hit with the search, then the passage, those stands for looking for was taken straight in paging. Then the search with another place from the K*y must again be accomplished. If we identified thus the old K*y and noted us the offset address, we can close Wordpad and delete the Hexdatei, since now the no more one does not use. The remainder is settled over the Multi_AES_K*Y_PATCHER. We open these and register as the first the offset address (in this case thus C7A86) with SELECT firmware offset. All the same which in it-stands before, the offset begins the existing entry up to the hyphen behind the hyphen, one deletes thus and registers behind it the new value. Now we load our firmware (the correct being file) in's Prog and click on "READ". In the right window now a 11zeilige appears passage from our firmware with the Nagra2-K*y at the beginning. In order to change these, we make on the right window one let us right-click and click "everything mark" (the passage blue underlaid). Now again ' nen right-click and on "copying" click. Next with the mouse on the left window, again one right-clicks makes and "inserting" goes to click. In this window the K*y can be worked on now carefully. If one comes in disorder thereby, one has always still the right window to the comparison. If the cookie was successfully exchanged, can be clicked on "Write" and the Patch is finished. As a check again for "READ" and now right and left window clicks again would have to be identical. The Prog can now be closed and the gepatchte Firm on the Kaon be played. D+ is now again bright...

 

Hopelijk heb je hier wat aan! Software staat op het eerder genoemde board.

Maak een account aan of log in om te reageren

Je moet een lid zijn om een reactie te kunnen achterlaten

Account aanmaken

Registreer voor een nieuwe account in onze community. Het is erg gemakkelijk!

Registreer een nieuwe account

Inloggen

Heb je reeds een account? Log hier in.

Nu inloggen
  • Wie is er online   0 leden

    • Er zijn geen geregistreerde gebruikers deze pagina aan het bekijken
×
×
  • Nieuwe aanmaken...