Ga naar inhoud


Terminal output op de UPC MediaBox via scart.

xinetic

Door xinetic
in Ziggo

 Delen

Aanbevolen berichten

xinetic Rijzende ster

xinetic

Geplaatst:
Geplaatst:

Allen,

 

Wellicht is dit wel een deuropening naar meer info over de UPC Mediabox.

Bij toeval ben ik er achter gekomen dat bij sommige apparaten met een scart aansluiting, dat je op pen 10,12,14 (data 1, data

 

2, data ground) data kunt uitlezen met een terminal programma in combinatie met een max232 converter ertussen (ivm spannings

 

niveau).

Ook dit geldt voor de UPC MediaBox.

Baudrate: 19200

Data Bits: 8

Parity: None

Stop Bits: 1

Flow Control: None

 

Onderstaande log krijg je als je de communicatie tot stand brengt en de MediaBox voorziet van Power:

 

%%LD : #################### LAUNCHER ####################

 

%%LD : Main board serial number : **********

 

%%LD : Launcher release number : 3.10

 

%%LD : Loader release number : 3.10

 

%%LD : Decoder IDs :

 

%%LD : OUI : 0x00-0x10-0x95

 

%%LD : hwUsageId : 0x00

 

%%LD : swUsageId : 0x00

 

%%LD : versionId : 0x0040

 

%%LD : PT : 0x0820

 

%%LD : PV : 0x0002

 

%%LD : PR : 0x0010

 

%%LD : flagSerialDownload = ON (0x01)

 

%%LD : flagInterruptible = OFF (0x00)

 

%%LD : MAC decoder address : **:**:**:**:**:**

 

%%LD : Nominal download triggered

 

%%LD : --------------------- LOADER ---------------------

 

%%LD : UPC_EUROPE_DCI5000

 

%%LD : @(#)Loader - Copyrights THOMSON R&D France - Version 3.10

 

%%LD : Apr 20 2005 - 14:19:52

 

%%LD : Download flag : 0x00000002 (RECOVERY DLD)

 

%%LD : Searching software update stream location ...

 

%%LD : Trying frontend set n°0 pid 0x1301

 

%%LD : Frequency = 164 MHz

 

%%LD : Symbol rate = 6900 KHz

 

%%LD : Modulation type = 3

 

%%LD : Carrier detected

 

%%LD : Trying section acquisition on PID : 0x1301

 

%%LD : Signal cut

 

˜æ

 

#APPSTOR DUMP >>>

#APPSTOR <<< DUMP

 

#SECURE:WARNING: / is not permanent

gdbo raw port not initialized

 

%% ID : Detected 5100 CUT2.0

#INTPRT[RESET] starting

[o_xyman_client_register] success: client = ********.

#INTPRT[RESET] init

%%GSQC : project = @(#)UPC_EUROPE_DCI52_00

 

%%GSQC : priv. ver = @(#)DCI5xUPC_SW1_93

 

%%GSQC : glob ID = 0x0000

 

%%GSQC : MIN = DCI52UPC

 

%%GSQC : MA = Not Applicable

 

%%GSQC : DRV = @(#)DCI52UPC_DRV_SW_R1_61

 

%%GSQC : osal = @(#)v1.5.8-2

 

%%GSQC : st20 = DCU_2.0.5_PATCH_2

 

%%GSQC : CA = @(#)ca_UPC_E_DCI52UPC_rel1_4

 

%%GSQC : optv = @(#)OpenTV EN23122

 

%%GSQC : serial nb = ************

 

%%GSQC : SW ver. = 1.93

 

%%GSQC : manuf ver = 52UPC01

 

%%GSQC : pti = 0x00030803

 

%%GSQC : tc = 0x00030803

 

%%GSQC : ret boot ver = 03.10.03.10

 

%%GSQC : ret SW ver = 1.93

 

[uCNP] RAM available = 8583816

[uCNP] Max segment

[uCNP] Manufacturer = THOMSON, OUID=

[uCNP] 52UPC01

[uCNP] 1.93

[uCNP] EN23122

[uCNP] 1.1.19

[uCNP] 03.10.03.10

Socket pair created : first = 1 and second = 2.

%% GINIT : decoder_hard_init_3

 

%%GSQC : OUI = 0x00 0x10 0x95

 

%%GSQC : UID = 0x00

 

%%GSQC : PT/PV = 0x08200002

 

%%GSQC : PR = 0x0010

 

%%GSQC : VID = 0x0040

 

%% GINIT : >>>>>> CASS INIT DONE <<<<<<

[TCP-IP_LINK] DNS Server IP addr reset OK !

[TCP-IP_LINK] o_link_open returned OK

[o_xyman_client_register] success: client = ********.

#INTPRT[RUNNING] running:0x2

[uCNP] CA msg received ALARM, 105

[TCP-IP_LINK] link notify => O_LINK_EVENT_LINKUP with cond 0

[TCP-IP_LINK] Following info retrieved from DOCSIS_SCM_QRY_NAME Sq&C :

[TCP-IP_LINK] STB IP Address ***.***.***.***

[TCP-IP_LINK] DHCP Addr ***.***.***.***

[TCP-IP_LINK] net mask ***.***.***.***

[TCP-IP_LINK] lease time 568295 seconds

[TCP-IP_LINK] Host name

[TCP-IP_LINK] Domain name chello.nl

[TCP-IP_LINK] Router Addr ***.***.***.***

[TCP-IP_LINK] Following DNS info retrieved from DHCP answer :

[TCP-IP_LINK] DNS server1 ***.***.***.***

[TCP-IP_LINK] DNS server2 ***.***.***.***

[TCP-IP_LINK] DNS data updated !!

[uCNP] CA msg received ALARM, 102

[uCNP] CA msg received NOTIFICATION, 104

[uCNP] CA msg received NOTIFICATION, 100

[uCNP] CA msg received NOTIFICATION, 103

[uCNP] CA msg received NOTIFICATION, 102

[uCNP] CA msg received NOTIFICATION, 101

-------------- nb link = 1 ,name = generic_gnplink

CASS_RPH => The return path link is now open.

 

Serienummer/macadres/ipadres heb ik vervangen voor ******

 

 

Data voor Nederland 1

 

[uCNP] Channel: 1, 62465, 0

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel component: TELETEXT_T

 

 

Data voor Reality

 

[uCNP] Channel: 19, 62465, 18

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel component: TELETEXT_T

[uCNP] Channel component: DVBST_T

[uCNP] Channel component: DVBST_T

[uCNP] Channel component: DVBST_T

[uCNP] Channel component: DVBST_T

[uCNP] Channel component: DVBST_T

[uCNP] Channel component: DVBST_T

[uCNP] Channel component: DVBST_T

[uCNP] Channel component: DVBST_T

[DVBST] DSS: Access granted: comp_page = 2 anci_page = 2

 

 

Data voor Canal+ (geen abonnement)

 

[uCNP] Channel: 102, 62465, 23

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel component: TELETEXT_T

[uCNP] CA msg received NOTIFICATION, 106

 

 

Data voor het indrukken van de "Guide"

 

#APPSTOR: appstore_verify_application

#APPSTOR: checking app flags

#APPSTOR: checking module flags

#INTPRT[RUNNING] exited, status:0x1

#INTPRT[CLEANING_UP] init

#INTPRT[LOADING] in progress

#INTPRT[LOADING] module

#INTPRT[LOADING] module

#INTPRT[LOADING] module

#INTPRT[RUNNING] running:0xffffffff

good trackswitch call

track_process_control_msg

MSG_TYPE_STATION_CONTROL:STREAM OFF: OPENTV, HANDLE 0x0, TRACK (0x00000000) 0x44 0x41 0x59 0x30

checking message_control_cond for C_STREAM_ON

unknown condition!

msgUsed is 1

#APPSTOR: appstore_verify_application

#APPSTOR: checking app flags

#APPSTOR: checking module flags

#APPSTOR: calling am_storing_request

track_process_control_msg

MSG_TYPE_STATION_CONTROL:STREAM ON: OPENTV, HANDLE 0x0, TRACK (0x44415930) 0x44 0x41 0x59 0x30

checking message_control_cond for C_STREAM_ON

message_control_cond C_STREAM_ON track 44415930

track_current_tag MATCH!

msgUsed is 1

 

 

Data voor de interactieve zender 3voor12

 

[uCNP] Channel: 614, 62465, 72

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel component: MODULE_T

[uCNP] Channel component: MODULE_T

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel component: MODULE_T

[uCNP] Channel component: MODULE_T

[uCNP] CA msg received NOTIFICATION, 106

#APPSTOR: appstore_verify_application

#APPSTOR: checking app flags

#APPSTOR: checking module flags

#INTPRT[RUNNING] exited, status:0x1

#INTPRT[CLEANING_UP] init

#INTPRT[LOADING] in progress

#INTPRT[RUNNING] running:0xffffffff

 

### --- Application Information --- ###

ApplicationId: CB4E0891-2DA3-4830-AA8-70B1CF5BD8F7

Time of compilation: 06 July 2006, 49:21:09

PMC version: 4.2.1.20

ETV-studio version: 4.2.1

Template version: 4.1.0.3

Application version: 2

### ------------------------------- ###

 

.1__STREAM_OFF; __ (track: 0, tuning req: 0, restore loaders: 1) __STREAM_OFF; switching to secondary PID 0x5345434f!!Station

 

control condition: 8; type: 79 Got a quit event. (reason: 4)Quiting....!#INTPRT[RUNNING] exited, status:0x1

#INTPRT[CLEANING_UP] init

#INTPRT[RUNNING] running:0x2

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel: 612, 62465, 71

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] CA msg received NOTIFICATION, 106

[uCNP] Channel: 614, 62465, 72

[uCNP] CA msg received NOTIFICATION, 106

[uCNP] Channel component: VIDEO_T

[uCNP] Channel component: AUDIO_T

[uCNP] Channel component: MODULE_T

[uCNP] Channel component: MODULE_T

[uCNP] CA msg received NOTIFICATION, 106

#APPSTOR: appstore_verify_application

#APPSTOR: checking app flags

#APPSTOR: checking module flags

#INTPRT[RUNNING] exited, status:0x1

#INTPRT[CLEANING_UP] init

#INTPRT[LOADING] in progress

#INTPRT[RUNNING] running:0xffffffff

 

### --- Application Information --- ###

ApplicationId: CB4E0891-2DA3-4830-AA8-70B1CF5BD8F7

Time of compilation: 06 July 2006, 49:21:09

PMC version: 4.2.1.20

ETV-studio version: 4.2.1

Template version: 4.1.0.3

Application version: 2

 

### ------------------------------- ###

 

.1__STREAM_OFF; __ (track: 0, tuning req: 0, restore loaders: 1) __STREAM_OFF; switching to secondary PID 0x5345434f!!Station

 

control condition: 8; type: 79 Failed to open cookie !!!!!!!!!!!__STREAM_OFF; __ (track: 1397048143, tuning req: 0, restore

 

loaders: 0) Station control condition: 8; type: 79 Station control condition: 8; type: 86 Station control condition: 8; type:

 

65 Station control condition: 4; type: 0 __C_PROGRAM_ON (handle: 0x00000000) Station control condition: 5; type: 0 Station

 

control condition: 9; type: 86 Station control condition: 9; type: 65 #APPSTOR: appstore_verify_application

#APPSTOR: checking app flags

#APPSTOR: checking module flags

Station control condition: 9; type: 79 Got a quit event. (reason: 1)Quiting....!#INTPRT[RUNNING] exited, status:0x1

#INTPRT[CLEANING_UP] init

#INTPRT[LOADING] in progress

#INTPRT[RUNNING] running:0xffffffff

 

### --- Application Information --- ###

ApplicationId: EDC9C62A-3A15-4131-8DE7-94E2C429E864

Time of compilation: 06 July 2006, 11:14:09

PMC version: 4.2.1.20

ETV-studio version: 4.2.1

Template version: 3.6.0.4

Application version: 2

### ------------------------------- ###

 

.1__STREAM_OFF; __ (track: 0, tuning req: 0, restore loaders: 1) __STREAM_OFF; switching to secondary PID 0x5345434f!!Station

 

control condition: 8; type: 79 #APPSTOR: appstore_verify_application

#APPSTOR: checking app flags

#APPSTOR: checking module flags

.4.4a.5Station control condition: 9; type: 79 Station control condition: 8; type: 65 Station control condition: 9; type: 65

 

.r.T(-1).r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897)

 

.r.r.T(897).r.r.T(897).r.T(897).r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(8

 

97).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).

 

r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.

 

T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(89

 

7).r.r.T(897).r.r.T(897).r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r

 

.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(8

 

97).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897).r.r.T(897)Got a quit event.

 

(reason: 4)Quiting....!#INTPRT[RUNNING] exited, status:0x1

#INTPRT[CLEANING_UP] init

#INTPRT[RUNNING] running:0x2

 

 

En ga zo maar door, wellicht is dit slechts het begin.

Heb alleen geen idee of je het bootproces ook kan onderbreken (net zoals bij een aantal routers, tijdens het booten 3x op de

 

spatiebalk drukken).

 

ALs je de modem intern ontkoppeld, krijg je tijdens het booten ook nog de melding

 

[uCNP] CA msg received ALARM, 105

 

 

Misschien ligt hier wel de methode om de BoxID uit te lezen, zodat ook de DBOX-II gebruikt kan worden.

 

 

Ik zou zeggen, pruts mee en vermeld maar wat je ontdekt hebt.

Link naar reactie
Delen op andere sites

xinetic Rijzende ster

xinetic

Geplaatst:
  • Auteur
Geplaatst:

Kijk hier voor de datasheet

 

Heb er niet echt een schema van, de max232 komt tussen de seriele poort van de pc en de scart aansluiting, maar onderstaande schema kun je ook wel gebruiken.

 

sch_max.gif

JP1 - sluit je op de compoort aan

JP3 - sluit je op de scartaansluiting aan

2 - op pen 14 van de scart

3 en 4 - op pen 10 en 12 van de scart (volgorde van deze 2 moet je ff uitproberen weet zo niet welke Tx of Rx is)

Link naar reactie
Delen op andere sites

Maak een account aan of log in om te reageren

Je moet een lid zijn om een reactie te kunnen achterlaten

Account aanmaken

Registreer voor een nieuwe account in onze community. Het is erg gemakkelijk!

Registreer een nieuwe account

Inloggen

Heb je reeds een account? Log hier in.

Nu inloggen
 Delen
Ga naar topic overzicht

  • Wie is er online   0 leden

    • Er zijn geen geregistreerde gebruikers deze pagina aan het bekijken
×
×
  • Nieuwe aanmaken...