OSCAM 0.99.4svn build #3146 icm Smargo leest CD kaart niet

[mr|repel]

Hoi allemaal,

 

Ik ben al een tijdje bezig met Tvheadend aan de gang te krijgen icm de smargo kaartlezer. Icm CCcam heb ik het goed werken, maar dan kan ik maar een "lijntje" openen, waardoor ik mijn tweede DVB-S kaart alleen FTA kan gebruiken.

 

Sinds een paar dagen ben ik aan de gang met OSCAM. Ik krijg het niet voor elkaar om de kaart juist in te lezen. Enkele settings:

 

oscam.server

Code:

[reader]label                         = canaldigitaalenable                        = 1protocol                      = mousedevice                        = /dev/ttyUSB0caid                          = 0100detect                        = cdmhz                           = 500cardmhz                       = 500ident                         =group                         = 1emmcache                      = 1,3,2auprovid                      =

 

 

oscam.conf

Code:

[global]nice          = -1WaitForCards  = 1#pidfile      = /var/run/oscam.pidlogfile       = /var/log/oscam/oscam.logusrfile       = /var/log/oscam/oscamuser.logcwlogdir      = /var/log/oscam/cw[monitor]port          = 988aulow         = 120monlevel      = 1[newcamd]key           = 0102030405060708091011121314port          = 10000@0100:00006A[webif]httpport = 81httprefresh = 5httpallowed = 192.168.0.1-192.168.255.255httphideidleclients = 0httpreadonly = 0[cccam]#port = 12000#cccversion = 2.1.2#cccbuild = 2892#reshare = 2#ignorereshare = 1#updateinterval = 240#minimizecards = 0

 

 

Ik krijg als output over de webif:

Code:

2011/02/07 18:55:50 12224 s reader started (pid=12388, device=/dev/ttyUSB0, detect=cd, mhz=500, cardmhz=500)2011/02/07 18:55:50 12388 r02 restarting reader canaldigitaal (index=0)2011/02/07 18:55:52 12388 r02 card detected2011/02/07 18:56:03 12388 r02 Error activating card.2011/02/07 18:56:13 12388 r02 Error activating card. 

en

Code:

2011/02/07 19:03:26 12571 r02 restarting reader canaldigitaal (index=0)2011/02/07 19:03:28 12571 r02 card detected2011/02/07 19:03:33 12571 r02 ATR: 3B F7 11 00 01 40 96 70 70 0A 0E 6C B6 D62011/02/07 19:03:34 12571 r02 Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz2011/02/07 19:03:35 12571 r02 card system not supported2011/02/07 19:03:35 12571 r02 Normal mode failed, reverting to Deprecated Mode2011/02/07 19:03:40 12571 r02 ATR: 3B F7 11 00 01 40 96 70 70 0A 0E 6C B6 D62011/02/07 19:03:41 12571 r02 Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz2011/02/07 19:03:42 12571 r02 card system not supported2011/02/07 19:03:42 12571 r02 card initializing error 

 

 

Ik heb het ook al met OSCAM 1.00 geprobeerd, maar geen succes. Op de een of andere manier wilt de kaart niet lezen. Wie o wie heeft een idee ?

[moonchild]

Oscam onder cygwin kan niet overklokken. Zet je reader op 3.579 MHz en in oscam.server: mhz=358

[mr|repel]

Bedankt voor de reactie, helaas haalt dit niets uit. Even voor de goede orde, ik draai op ClearOS (Linux)

[mr|repel]

Ik ben nog steeds aan het knutselen en al iets verder, maar nog geen succes Ik heb nu versie 1.00 build 4736 draaien.

Code:

2011/02/20 12:23:49 B77936C0 s version=1.00-unstable_svn, build #4736, system=i686-pc-linux, nice=-12011/02/20 12:23:49 B77936C0 s client max. idle=120 sec, debug level=02011/02/20 12:23:49 B77936C0 s max. logsize=unlimited2011/02/20 12:23:49 B77936C0 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=0 ms2011/02/20 12:23:49 B77936C0 s auth size=49722011/02/20 12:23:49 B77936C0 s Cannot open file "/usr/local/etc/oscam.services" (errno=2)2011/02/20 12:23:49 B77936C0 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled2011/02/20 12:23:49 B77936C0 s signal handling initialized (type=sysv)2011/02/20 12:23:49 B77936C0 s can't open file "/usr/local/etc/oscam.srvid" (err=2), no service-id's loaded2011/02/20 12:23:49 B77936C0 s can't open file "/usr/local/etc/oscam.tiers" (err=2), no tier-id's loaded2011/02/20 12:23:49 B77936C0 s can't open file "/usr/local/etc/oscam.provid" (err=2), no provids's loaded2011/02/20 12:23:49 B77936C0 s can't open file "/usr/local/etc/oscam.ird" (errno=2) irdeto guessing not loaded2011/02/20 12:23:49 B77936C0 s monitor: initialized (fd=8, port=988)2011/02/20 12:23:49 B77936C0 s camd33: disabled2011/02/20 12:23:49 B77936C0 s camd35: disabled2011/02/20 12:23:49 B77936C0 s cs378x: disabled2011/02/20 12:23:49 B77936C0 s newcamd: initialized (fd=9, port=10000, crypted)2011/02/20 12:23:49 B77936C0 s CAID: 01002011/02/20 12:23:49 B77936C0 s provid #0: 00006A2011/02/20 12:23:49 B77936C0 s cccam: disabled2011/02/20 12:23:49 B77936C0 s radegast: disabled2011/02/20 12:23:49 B77936C0 s http thread started2011/02/20 12:23:49 B77936C0 s creating thread for device /dev/ttyUSB02011/02/20 12:23:49 B77842A0 r reader thread started (thread=B77842A0, label=canaldigitaal, device=/dev/ttyUSB0, detect=cd, mhz=358, cardmhz=358)2011/02/20 12:23:49 B778B2A0 h HTTP Server listening on port 88882011/02/20 12:23:49 B77936C0 s loadbalancer: can't read from file /tmp/.oscam/stat2011/02/20 12:23:49 B77936C0 s waiting for local card init 2011/02/20 12:23:51 B77842A0 r canaldigitaal card detected2011/02/20 12:23:56 B77842A0 r ATR: 3B F7 11 00 01 40 96 70 70 0A 0E 6C B6 D62011/02/20 12:23:57 B77842A0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 3.58 Mhz2011/02/20 12:23:58 B77842A0 r type: SECA, caid: 0100, serial: 57141XXXX, card: Canal+ NL v10.02011/02/20 12:23:58 B77842A0 r card system not supported2011/02/20 12:23:58 B77842A0 r Normal mode failed, reverting to Deprecated Mode2011/02/20 12:24:03 B77842A0 r ATR: 3B F7 11 00 01 40 96 70 70 0A 0E 6C B6 D62011/02/20 12:24:04 B77842A0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 3.58 Mhz2011/02/20 12:24:05 B77842A0 r type: SECA, caid: 0100, serial: 57141XXXX, card: Canal+ NL v10.02011/02/20 12:24:05 B77842A0 r card system not supported2011/02/20 12:24:05 B77842A0 r card initializing error2011/02/20 12:24:05 B77936C0 s init for all local cards done2011/02/20 12:24:05 B77936C0 s anti cascading disabled 

 

Ik krijg de serial e.d. uitgelezen, maar daar houd het ook mee op.

[mr|repel]

Succes

 

Code:

2011/02/20 13:21:01 B77162A0 r canaldigitaal card detected2011/02/20 13:21:03 B77162A0 r ATR: 3B F7 11 00 01 40 96 70 70 0A 0E 6C B6 D62011/02/20 13:21:04 B77162A0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz2011/02/20 13:21:05 B77162A0 r type: SECA, caid: 0100, serial: 57141XXXX, card: Canal+ NL v10.02011/02/20 13:21:05 B77162A0 r [seca-reader] provider: 1, valid: 1, name: MANAGMENT, expiry date: 2011/04/102011/02/20 13:21:05 B77162A0 r [seca-reader] SA: 1107901E2011/02/20 13:21:05 B77162A0 r [seca-reader] provider: 2, valid: 1, name: CANALDIGITAAL, expiry date: 2011/04/162011/02/20 13:21:05 B77162A0 r [seca-reader] SA: 00354CEF2011/02/20 13:21:05 B77162A0 r providers: 2 (0000,006A)2011/02/20 13:21:05 B77162A0 r [seca-reader] parental locked2011/02/20 13:21:05 B77162A0 r [seca-reader] ready for requests2011/02/20 13:21:05 B77162A0 r found cardsystem seca2011/02/20 13:21:05 B77162A0 r [seca-reader] no PBM for provider 12011/02/20 13:21:05 B77162A0 r [seca-reader] PBM for provider 2: C2800000000000002011/02/20 13:21:05 B77256C0 s init for all local cards done2011/02/20 13:21:05 B77256C0 s anti cascading disabled2011/02/20 13:21:05 B770F2A0 c client connected to 10000 port2011/02/20 13:21:05 B770F2A0 c encrypted newcamd:10000-client 127.0.0.1 granted (hts, au=on (1 reader))2011/02/20 13:21:05 B770F2A0 c user hts authenticated successfully (generic)2011/02/20 13:21:05 B770F2A0 c AU enabled for user hts on reader canaldigitaal2011/02/20 13:21:06 B770F2A0 c hts (0100&00006A/0FAF/64:C379): found (300 ms) by canaldigitaal (of 1 avail 1) - 0100:0FAF unknown2011/02/20 13:21:13 B770F2A0 c hts (0100&00006A/0FAF/64:7F5B): found (305 ms) by canaldigitaal (of 1 avail 1) - 0100:0FAF unknown2011/02/20 13:21:23 B770F2A0 c hts (0100&00006A/0FAF/64:4781): found (290 ms) by canaldigitaal (of 1 avail 1) - 0100:0FAF unknown2011/02/20 13:21:33 B770F2A0 c hts (0100&00006A/0FAF/64:D072): found (291 ms) by canaldigitaal (of 1 avail 1) - 0100:0FAF unknown2011/02/20 13:21:43 B770F2A0 c hts (0100&00006A/0FAF/64:6738): found (290 ms) by canaldigitaal (of 1 avail 1) - 0100:0FAF unknown 

 

ik heb de oscam.server als volgt aan moeten passen:

Code:

[reader]label                         = canaldigitaalenable                        = 1protocol                      = smargodevice                        = /dev/ttyUSB0caid                          = 0100detect                        = cdmhz                           = 500cardmhz                       = 500ident                         =group                         = 1emmcache                      = 1,3,2auprovid                      =

 

Zoals je ziet staat deze nu op smargo en niet mouse

[mr|repel]

nu breekt mn klomp.....

 

Server opnieuw gestart:

Code:

2011/02/20 14:05:46 B77842A0 r canaldigitaal card detected2011/02/20 14:05:54 B77842A0 r Error activating card. 

[mr|repel]

Een uitgebreider log:

 

Code:

------------------------------------------------------------------------------->> OSCam <<  cardserver started at Sun Feb 20 14:26:54 2011-------------------------------------------------------------------------------2011/02/20 14:26:54 B77482A0 r >> OSCam <<  cardserver started version 1.00-unstable_svn, build #4736 (i686-$2011/02/20 14:26:54 B77482A0 r version=1.00-unstable_svn, build #4736, system=i686-pc-linux, nice=-12011/02/20 14:26:54 B77482A0 r client max. idle=120 sec, debug level=2552011/02/20 14:26:54 B77482A0 r max. logsize=10 Kb2011/02/20 14:26:54 B77482A0 r client timeout=5000 ms, fallback timeout=2500 ms, cache delay=0 ms2011/02/20 14:26:54 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:26:54 B77482A0 r IO: Setting RTS=12011/02/20 14:26:54 B77482A0 r IO: Setting RTS=02011/02/20 14:26:55 B77482A0 r TIMEOUT in IO_Serial_WaitToRead2011/02/20 14:26:55 B77482A0 r IO: Receiving:2011/02/20 14:26:55 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:26:55 B77482A0 r ERROR, function call reader->crdr.activate(reader, atr) returns error.2011/02/20 14:26:55 B77482A0 r Error activating card.2011/02/20 14:26:56 B77482A0 r IFD: Activating card in reader canaldigitaal2011/02/20 14:26:56 B77482A0 r Smargo: Resetting card:2011/02/20 14:26:56 B77482A0 r Smargo: sending F=0174 (372), D=01 (1), Freq=1388 (5000), N=00 (0), T=00 (0),$2011/02/20 14:26:56 B77482A0 r IO: Sending:2011/02/20 14:26:56 B77482A0   01 01 74 012011/02/20 14:26:56 B77482A0 r IO: Sending:2011/02/20 14:26:56 B77482A0   02 13 882011/02/20 14:26:56 B77482A0 r IO: Sending:2011/02/20 14:26:56 B77482A0   03 002011/02/20 14:26:56 B77482A0 r IO: Sending:2011/02/20 14:26:56 B77482A0   04 002011/02/20 14:26:56 B77482A0 r IO: Sending:2011/02/20 14:26:56 B77482A0   05 002011/02/20 14:26:56 B77482A0 r IFD: Setting parity from Even to Even2011/02/20 14:26:56 B77482A0 r TIMEOUT in IO_Serial_WaitToRead2011/02/20 14:26:56 B77482A0 r IO: Receiving:2011/02/20 14:26:56 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:26:56 B77482A0 r IO: Setting RTS=12011/02/20 14:26:57 B77482A0 r IO: Setting RTS=02011/02/20 14:26:58 B77482A0 r TIMEOUT in IO_Serial_WaitToRead2011/02/20 14:26:58 B77482A0 r IO: Receiving:2011/02/20 14:26:58 B77482A0   0E 6C B6 D6 90 00 00 F7 FD 24 30 C0 01 33 2F 242011/02/20 14:26:58 B77482A0   FF 3B F7 01 40 96 0A2011/02/20 14:26:58 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:26:58 B77482A0 r Smargo ATR: 23 bytes2011/02/20 14:26:58 B77482A0   0E 6C B6 D6 90 00 00 F7 FD 24 30 C0 01 33 2F 242011/02/20 14:26:58 B77482A0   FF 3B F7 01 40 96 0A2011/02/20 14:26:58 B77482A0 r Smargo: sending F=0174 (372), D=01 (1), Freq=1388 (5000), N=00 (0), T=00 (0),$2011/02/20 14:26:58 B77482A0 r IO: Sending:2011/02/20 14:26:58 B77482A0   01 01 74 012011/02/20 14:26:58 B77482A0 r IO: Sending:2011/02/20 14:26:58 B77482A0   02 13 882011/02/20 14:26:58 B77482A0 r IO: Sending:2011/02/20 14:26:58 B77482A0   03 002011/02/20 14:26:58 B77482A0 r IO: Sending:2011/02/20 14:26:58 B77482A0   04 002011/02/20 14:26:58 B77482A0 r IO: Sending:2011/02/20 14:26:58 B77482A0   05 002011/02/20 14:26:58 B77482A0 r IFD: Setting parity from Even to Odd2011/02/20 14:26:58 B77482A0 r IO: Setting properties2011/02/20 14:26:59 B77482A0 r TIMEOUT in IO_Serial_WaitToRead2011/02/20 14:26:59 B77482A0 r IO: Receiving:2011/02/20 14:26:59 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:26:59 B77482A0 r IO: Setting RTS=12011/02/20 14:26:59 B77482A0 r IO: Setting RTS=02011/02/20 14:27:00 B77482A0 r TIMEOUT in IO_Serial_WaitToRead2011/02/20 14:27:00 B77482A0 r IO: Receiving:2011/02/20 14:27:00 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:27:00 B77482A0 r Smargo: sending F=0174 (372), D=01 (1), Freq=1388 (5000), N=00 (0), T=00 (0),$2011/02/20 14:27:00 B77482A0 r IO: Sending:2011/02/20 14:27:00 B77482A0   01 01 74 012011/02/20 14:27:00 B77482A0 r IO: Sending:2011/02/20 14:27:00 B77482A0   02 13 882011/02/20 14:27:00 B77482A0 r IO: Sending:2011/02/20 14:27:00 B77482A0   03 002011/02/20 14:27:00 B77482A0 r IO: Sending:2011/02/20 14:27:00 B77482A0   04 002011/02/20 14:27:00 B77482A0 r IO: Sending:2011/02/20 14:27:00 B77482A0   05 002011/02/20 14:27:00 B77482A0 r IFD: Setting parity from Odd to None2011/02/20 14:27:00 B77482A0 r IO: Setting properties2011/02/20 14:27:01 B77482A0 r TIMEOUT in IO_Serial_WaitToRead2011/02/20 14:27:01 B77482A0 r IO: Receiving:2011/02/20 14:27:01 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:27:01 B77482A0 r IO: Setting RTS=12011/02/20 14:27:01 B77482A0 r IO: Setting RTS=02011/02/20 14:27:02 B77482A0 r TIMEOUT in IO_Serial_WaitToRead2011/02/20 14:27:02 B77482A0 r IO: Receiving:2011/02/20 14:27:02 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:27:02 B77482A0 r Smargo: sending F=026A (618)$2011/02/20 14:27:02 B77482A0 r IO: Sending:2011/02/20 14:27:02 B77482A0   01 02 6A 012011/02/20 14:27:02 B77482A0 r IO: Sending:2011/02/20 14:27:02 B77482A0   02 17 702011/02/20 14:27:02 B77482A0 r IO: Sending:2011/02/20 14:27:02 B77482A0   03 002011/02/20 14:27:02 B77482A0 r IO: Sending:2011/02/20 14:27:02 B77482A0   04 012011/02/20 14:27:02 B77482A0 r IO: Sending:2011/02/20 14:27:02 B77482A0   05 002011/02/20 14:27:02 B77482A0 r IFD: Setting parity from Non$2011/02/20 14:27:02 B77482A0 r IO: Setting properties2011/02/20 14:27:02 B77482A0 r TIMEOUT in IO_Serial_WaitToR$2011/02/20 14:27:02 B77482A0 r IO: Receiving:2011/02/20 14:27:02 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:27:02 B77482A0 r IO: Setting RTS=12011/02/20 14:27:03 B77482A0 r IO: Setting RTS=02011/02/20 14:27:04 B77482A0 r TIMEOUT in IO_Serial_WaitToR$2011/02/20 14:27:04 B77482A0 r IO: Receiving:2011/02/20 14:27:04 B77482A0 r TIMEOUT in IO_Serial_Read2011/02/20 14:27:04 B77482A0 r ERROR, function call reader-$2011/02/20 14:27:04 B77482A0 r Error activating card.2011/02/20 14:27:04 B77482A0 r card initializing error2011/02/20 14:27:04 B77576C0 s init for all local cards done2011/02/20 14:27:04 B77576C0 s anti cascading disabled2011/02/20 14:27:04 B77412A0 c cccam: failed ret: -12011/02/20 14:27:04 B77412A0 c anonymous disconnected  from$2011/02/20 14:27:04 B77412A0 c thread B77412A0 ended!2011/02/20 14:27:04 B77412A0 c encrypted cccam-client 192.1$2011/02/20 14:27:04 B77412A0 c cccam: send ack:2011/02/20 14:27:04 B77412A0   43 43 63 61 6D 00 00 00 00 0$2011/02/20 14:27:04 B77412A0   00 00 00 002011/02/20 14:27:04 B77412A0 c cccam: cli data:2011/02/20 14:27:04 B77412A0   4F 00 00 5D 64 72 65 61 6D 0$2011/02/20 14:27:04 B77412A0   00 00 00 00 00 00 00 00 B5 1$2011/02/20 14:27:04 B77412A0   01 32 2E 31 2E 34 00 00 00 0$2011/02/20 14:27:04 B77412A0   00 00 00 00 00 00 00 00 00 0$2011/02/20 14:27:04 B77412A0   00 33 31 39 31 00 00 00 00 0$2011/02/20 14:27:04 B77412A0   00 00 00 00 00 00 00 00 00 0$2011/02/20 14:27:04 B77412A0   00

 

Het lijkt of er een een of andere timeout plaatsvind.

 

 

 

 

[mr|repel]

Ik laat nu oscam connecten naar mijn cccam server (zelfde machine). Hierdoor kan ik met tvheadend toch meerdere connecties maken. Het nadeel is wel dat mijn "reactietijd" van +/- 200mS nu naar +/- 500mS is gegaan omdat ik via oscam naar mn cccam ga.

[Tech]

Ten eerste:

 

protocol moet niet zijn smargo maar :

 

protocol = smartreader

 

Verder kan het zijn dat de gebruikte frequenties roet in het eten gooien, ik gebruik iets andere waarden waarmee de zaak wel werkt:

 

caid = 0100

detect = cd

mhz = 480

cardmhz = 357

 

 

[mr|repel]

Helaas,

 

Als ik smartreader gebruik krijg ik de poort niet eens geopend:

Code:

2011/02/20 19:40:43 B76F12A0 r reader thread started (thread=B76F12A0, label=canaldigitaal, device=/dev/ttyUSB0, detect=cd, mhz=480, cardmhz=357)2011/02/20 19:40:43 B77006C0 s loadbalancer: can't read from file /tmp/.oscam/stat2011/02/20 19:40:43 B76F12A0 r IFD: Opening device /dev/ttyUSB02011/02/20 19:40:43 B77006C0 s waiting for local card init2011/02/20 19:40:43 B76F12A0 r ERROR, you have specified 'protocol = smartreader' in oscam.server,2011/02/20 19:40:43 B76F12A0 r recompile with SmartReader support.2011/02/20 19:40:43 B76F12A0 r Cannot open device: /dev/ttyUSB0 

 

De .conf die ik gebruik is:

Code:

[reader]label                         = canaldigitaalenable                        = 1protocol                      = smartreaderdevice                        = /dev/ttyUSB0caid                          = 0100detect                        = cdmhz                           = 480cardmhz                       = 357ident                         =group                         = 1emmcache                      = 1,3,2auprovid                      =

 

Kan je anders jou .conf file eens hier posten ?

 

P.S. deze settings met smargo als protocol werken ook niet..

[Tech]

Klopt, de smargo kan niet via een poort geconnect worden, dit is al een tijdje het geval in OsCam, vandaar dat in de webif de optie zit om de USB poorten te scannen.

 

Stel er komt iets uit zoals hieronder

 

Bus 003 Device 002: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC

 

daar zie je dat op bus 002 device 002 de lezer is gevonden, deze vul je dan als volgt in:

 

device = 003:002

 

Ik denk dat die dan wel werkt

 

Voorbeeld van een complete instelling :

 

[reader]

label = usb-seca-hd

enable = 1

protocol = smartreader

device = 003:002

caid = 0100

detect = cd

mhz = 480

cardmhz = 357

ident =

group = 1

emmcache = 1,1,10

lb_weight = 100

 

 

 

[mr|repel]

Bedankt voor je reactie !

 

Op de een of andere manier doet mijn oude instelling het weer na wat spelen met de .conf file. Morgen doe ik de server eens opnieuw starten om te kijken of dan ook alles nog werkt. Zo niet, dan ga ik ook eens met deze conf aan de slag. Als ik de cardserver herstart gaat alles goed, maar ja.... dat was vanmiddag ook tot ik de pc opnieuw startte.

 

Het lijkt net of de reader even over een drempel moet voordat hij werkt, echt een rare zaak... Zoals je onder ziet start hij nu weer zonder ellende op /dev/ttyUSB0

 

Code:

2011/02/20 20:23:40 B776D2A0 r reader thread started (thread=B776D2A0, label=canaldigitaal, device=/dev/ttyUSB0, detect=cd, mhz=500, cardmhz=500)2011/02/20 20:23:40 B777C6C0 s loadbalancer: can't read from file /tmp/.oscam/stat2011/02/20 20:23:40 B776D2A0 r smargo init2011/02/20 20:23:40 B777C6C0 s waiting for local card init2011/02/20 20:23:40 B776D2A0 r canaldigitaal card detected2011/02/20 20:23:42 B776D2A0 r ATR: 3B F7 11 00 01 40 96 70 70 0A 0E 6C B6 D6 2011/02/20 20:23:42 B776D2A0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz2011/02/20 20:23:43 B776D2A0 r type: SECA, caid: 0100, serial: 571416636, card: Canal+ NL v10.02011/02/20 20:23:44 B776D2A0 r [seca-reader] provider: 1, valid: 1, name: MANAGMENT, expiry date: 2011/04/102011/02/20 20:23:44 B776D2A0 r [seca-reader] SA: 1107901E2011/02/20 20:23:44 B776D2A0 r [seca-reader] provider: 2, valid: 1, name: CANALDIGITAAL, expiry date: 2011/04/162011/02/20 20:23:44 B776D2A0 r [seca-reader] SA: 00354CEF2011/02/20 20:23:44 B776D2A0 r providers: 2 (0000,006A)2011/02/20 20:23:44 B776D2A0 r [seca-reader] parental locked2011/02/20 20:23:44 B776D2A0 r [seca-reader] ready for requests2011/02/20 20:23:44 B776D2A0 r found cardsystem seca2011/02/20 20:23:44 B776D2A0 r [seca-reader] no PBM for provider 12011/02/20 20:23:44 B776D2A0 r [seca-reader] PBM for provider 2: C2800000000000002011/02/20 20:23:44 B777C6C0 s init for all local cards done2011/02/20 20:23:44 B777C6C0 s anti cascading disabled

[mr|repel]

Helaas loopt na circa 30 minuten de ECM tijd op naar 5 seconden (newcam icm Tvheadend). Cccam (in Oscam) blijft rond de 200 milli seconden (DM7000S). Nu weer Cccam aan het lopen met preload waardoor ik goede tijden heb, maar helaas maar een lijntje kan openen waardoor ik op een tuner alleen FTA kan zien.