[DBOX-II] Wie heeft de orginele CD S2 update binnen?

[Gast]

dus die gbox zit er in ? thx ff proberen en je hebt gewoon de update onder gbox ?ga ik dat vanmiddag proberen thx

edit : kan je me een pm sturen van waar je hem gedownload hebt die van 18-2-2005 ? want ik zie hem niet op het 3 leterboard met jaartal <img src="/ubbthreads/images/graemlins/smile.gif" alt="" />

[CEASAR W]

IK heb gisteren avond de ru dbox2 18-02 er opnieuw opgezet zonder instellingen te wijzigen op gbox en herstart maar kaart blijft op maart staan <img src="/ubbthreads/images/graemlins/kweetniet.gif" alt="" />

ceasar

[Unetwork]

Hoe zie je dit dan? bedoel datie op maart staat..

[CEASAR W]

Mijn kaart staat nog op 31-maart. dit controleer ik in het menu van een orginele seca tuner (abo informatie). ik kan hem met aangesloten lnb wel updaten maar ik wil de dbox2 ook graag AU hebben. Dus ik twijfel er aan of jou kaart wel op 30-04 staat.(ik heb de multicam ook al gewisseld)

ceasar

[CEASAR W]

Wie wil er eens even naar deze 2 bestanden kijken voor de au update ;cardserver- en gbox- config

#

# /var/tuxbox/config/cardserv.cfg

#

# The new cardserver can run several cards at once. It detects cards being

# inserted and removed from configured card readers. Every card uses its

# own TCP port to listen for incoming client connections. Card readers, that

# are configured, but where no card is inserted, will not be initialized.

# Supported are both serial ports of dbox2 (SERIAL_PORT = 0, 1), Dreambox

# cardreaders (SERIAL_PORT = 0 (upper), SERIAL_PORT = 1 (lower)) and the

# Dreambox's serial port (SERIAL_PORT = 2). Supported CA systems are Seca,

# Viaccess, Irdeto, Conax, Cryptoworks and Nagra1. Irdeto cards (or some of

# them) probably won't work in the Dreambox cardreaders, due to driver issues.

# In fact, the only Irdeto cards, that were successfully tested in Dreambox

# cardreaders, are the new Premiere cards and I2 cards. Premiere cards will ONLY

# work with betad (no sharing allowed for Premiere). Betad is a small subset

# of cardserver, using Unix Domain Sockets to communicate with newcamd. Also

# betad will only understand a very small subset of the options described here.

# Each instance of betad will only be able to serve exactly one card, while one

# instance of cardserver can serve multiple cards at the same time. Therefore

# betad is not able to handle the sc8in1. Betad configuration file is called

# betad.cfg. There is no special manual for betad.cfg, we everyone will be able

# to figure out, which cardserv.cfg options, described below, will also work in

# betad.cfg and which won't.

# Configuration consists of global (all cards) and local (single card) options.

# betad.cfg will of course only have one local (single card) section. The

# global section is located at the beginning of the file before the first

# SERIAL_PORT option. The SERIAL_PORT option is a "divider" between the global

# and the local sections, it also is a divider between options for different

# cards. The SC8IN1_SLOT options is a similar divider, but it divides only

# between different cards in the sc8in1 cam and the first SC8IN1_SLOT options

# has to preceeded by a SERIAL_PORT option. Some options may appear in the

# global as well as in local sections, in the case the option in the global

# section is a default for all cards, that don't have the same option in their

# particular local section. Options that appear in an incorrect section will

# be rejected with a "parse error" and the cardserver won't start. Betad will

# also reject all cardserver options, that aren't necessary or allowed for its

# operation. betad will understand the following options, of used correctly:

# SERIAL_PORT, BAUDRATE, USER, PARITY, CARD_DETECT_INVERT, CARD_DETECT_BIT and

# IGNORE_CARD_DETECT_SWITCH.

#

# You can also start cardserver multiple times by specifying different cfg

# files in the command line. Use only the name of the cfg file, the path of the

# file is always fixed to /var/tuxbox/config (dbox2, Dreambox) or /etc (i386)

#

# (G) = global section only

# (L) = local section only

# (A) = all sections

#

# 14 byte des key for the connection (A)

# DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14

#

# id name of the cardserver (G)

# SERVER_NAME = cardserv

#

# debug port, lists all cards and their open connections (G)

# just telnet to it

# DEBUG_PORT = 12002

#

# entitlement port, lists entitlements of Seca, Conax and Cryptoworks cards

# just telnet to it

# ENTITLEMENT_PORT = 12003

#

# optional admin options (G)

# port for incoming camdcmd connections

# password and 14 byte des key for admin connections

# ADMIN_PORT = 12004

# ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00

#

# Userlist (A)

# there can be multiple users, user 1 always do AU for the card

# additional AU users can be defined by adding "au" at the end of the USER line

# keep in mind that your card number will be sent to all AU users

# global user preceed local users in terms of userid

# lan/wan/spider gives the type of connection

# lan = local area network

# wan = wide area network (those connections can be rebuild with camdcmd wanon)

# connections from cardspider to "wan" declared cards in cardserver are not

# possible

# spider = acts like wan, but allows connections from cardspider

# <username> <password> <lan/wan/spider> <newcamd hostname> <newcamd incoming cws port> (A)

# everything starting from <lan/wan> is optional (reverse login is optional)

# USER = dummy dummy lan dbox2 12000

# two examples for additional AU users

# USER = dummy2 dummy2 lan dbox2 12000 au

# USER = dummy3 dummy3 au

#

# CLIENT_CONNECT_TIMEOUT (in 100ms) (G)

# max time to wait for a login at a newcamd client

# CLIENT_CONNECT_TIMEOUT = 20

#

# debug options (A) - show network and card init, ecm and emm packages

# DEBUG_INIT = no

# DEBUG_NET = no

# DEBUG_ECM = no

# DEBUG_EMM = no

#

# Serial Port (Phoenix/Multicam) (Section divider)

# The first SERIAL_PORT options ends the global section

# On Dreambox SERIAL_PORT = 0 is the upper card slot,

# SERIAL_PORT = 1 is the lower card slot and 2 is the

# actual serial port.

# All numbers SERIAL_PORT = 3 and higher on Dreambox will use /dev/usb/tts/X

# devices for Phoenix on USB-to-RS232 adapters. This feature depends on a

# driver for your particular SB->RS232 adapter being insmod into the kernel of

# your image, your particular USB->RS232 driver supporting RS232 handshaking

# signal generation and on the particular card used. Basically this feature

# should be considered unstable and for advanced users only. The BAUDRATE option

# is not available for SERIAL_PORT = 3 and higher on Dreambox and would be

# rejected with a parse error

# SERIAL_PORT = <no> begins a single card's local section

# SERIAL_PORT = 0

#

# Serial Port (sc8in1) (section devider)

# SERIAL_PORT = <no> sc8in1 begins a sc8in1 description

# SC8IN1_SLOT must follow immediately to start a local section

# SERIAL_PORT = 1 sc8in1

#

# sc8in1 slot (sc8in1 sub section divider)

# valid slots are 0-7, 0 being the left most connector on the sc8in1

# SC8IN1_SLOT = 1

#

# Parity - serial communication parameter for the smartcard (L)

# The default is on, which is correct for all cards except Irdeto

# This is for reading the ATR only, after the ATR has been recognized by

# cardserver, it automatically switches to the correct communication parameters

# Some Irdeto cards work with PARITY = on also, some need PARTIY = off, so just

# test it. Dreambox cardreaders don't need this option, so it will be rejected

# for SERIAL_PORT = 0, 1 on Dreambox

# PARITY = on

#

# CARD_DETECT_BIT (L)

# different Phoenix readers sometimes use different serial lines to detect an

# inserted card, here you can specify, which line cardserver should use for a

# particular card. Possible values are CTS, DCD and DSR

# Default is CTS for sc8in1 and dbox2 serport 1, DCD otherwise

# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)

# CARD_DETECT_BIT = DCD

#

# Baudrate (L) (DBOX2/DREAMBOX versions ONLY!)

# Baudrate selection for the dbox2/Dreambox server. Allows to run 6 MHz with

# 3.579 MHz crystal and (theoretically) the other way around.

# Keep in mind, running anything but Irdeto cards at 6 MHz is overclocking!!!

# Irdeto card at 3.57 MHz: BAUDRATE = 5727

# other card at 6 MHz: BAUDRATE = 16128

# Default is 9622, which is correct for all except Irdeto cards at 3.579 MHz

# 3579545 Hz / 372 = 9622 bit/s (see iso 7816)

# This option will be rejected on I386 and on Dreambox ports other than

# SERIAL_PORT = 2

# BAUDRATE = 9622

#

# TCP port (L) - the port listening for connections for a particular card

# TCP_PORT = 2000

#

# EMM options - block EMM-U, EMM-G or EMM-S (A)

# EMM-G = no

# EMM-S = no

# EMM-U = no

#

# For iso cardreaders that close the card switch contact instead of opening it,

# when a card is inserted (L)

# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)

# CARD_DETECT_INVERT = yes

#

# Disable Pin (L) Seca only

# suppress all pin enter requests on Seca cards

# be very careful with this feature, if you have ordered PPV events or have

# prepaid Jetons on your card, if this is enabled, cardserver will use them

# up on any ppv event without ever asking

# DISABLE_PIN = yes

#

# Special features (only for some cards) (L)

# SPECIAL_FEATURES = no

#

# Exclude services - Some providers offer a PPV preview by allowing a card

# to decrypt a certain number of ECMs of each PPV event before it has to be

# bought. Sharing such a card with other people allows them to "steal" this

# PPV preview. With this option, you can tell cardserver to not ask the card

# to decrypt ECMs for certain services, except if user 1 (the EMM user) asks

# for them. Each blocked service has to be listed with its service id.

# A service id is a 16-bit number and has to be given in hex.

# camdcmd offers a possibility to change the list of blocked services without

# restarting cardserver (if for example you have bought a PPV event and now

# want to share it).

#

# Block single service (L)

# EXCLUDE_SERVICE = 13a9

# You can also block a range of service ids, the following blocks all services

# from 02be to 02c8

# EXCLUDE_SERVICE_MULTIPLE = 02be:02c8

#

# Boxkey (for Nagra1 cards only) (L)

# 8 byte des boxkey of your nagra smartcard. This boxkey is needed for proper

# use of your card, otherwise you'll get incorrect control words

# BOXKEY = 11 22 33 44 55 66 77 88

#

# Example

#

DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14

SERVER_NAME = dbox

DEBUG_PORT = 14000

ENTITLEMENT_PORT = 14001

ADMIN_PORT = 14002

ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00

USER = dummy dummy lan localhost 12000

USER = dummy2 dummy2 lan localhost 12000

DEBUG_INIT = no

DEBUG_NET = no

DEBUG_ECM = no

DEBUG_EMM = no

#

# Canal Digital Nordic, Phoenix (3.57 MHz) @ ttyS0

#

#SERIAL_PORT = 0

#TCP_PORT = 10000

#CARD_DETECT_BIT = DCD

#EXCLUDE_SERVICE_MULTIPLE = 02be:02c8

#EXCLUDE_SERVICE_MULTIPLE = 0321:032a

#

# SC8IN1 (0,3,6,7 = empty, 1-2 = 3.57 MHz, 4 = 6 MHz, 5 = 4.43 MHz) @ ttyS1

#

#SERIAL_PORT = 1 sc8in1

#

# Czechlink (3.57 MHz) all EMM blocked

#

#SC8IN1_SLOT = 1

#TCP_PORT = 10001

#CARD_DETECT_INVERT = yes

#EMM-G = no

#EMM-S = no

#EMM-U = no

#

# Slovaklink (3.57 MHz) all EMM blocked

# Special features enabled <img src="/ubbthreads/images/graemlins/smile.gif" alt="" />

#

#SC8IN1_SLOT = 2

#TCP_PORT = 10002

#CARD_DETECT_INVERT = yes

#EMM-G = no

#EMM-S = no

#EMM-U = no

#SPECIAL_FEATURES = yes

#

# Canal Digital NL Irdeto (6 MHz)

#

#SC8IN1_SLOT = 4

#TCP_PORT = 10004

#BAUDRATE = 9600

#PARITY = off

#CARD_DETECT_INVERT = yes

#

# Viasat (4.43 MHz) - one additional user with no reverse login support

#

#SC8IN1_SLOT = 5

#TCP_PORT = 10005

#BAUDRATE = 11909

#USER = dummy3 dummy3

 

# 6Mhz!

#78Mhz = 14100

#79Mhz = 13900

#82Mhz = 13400

#84Mhz = 12700

SERIAL_PORT = 1

BAUDRATE = 16128

CARD_DETECT_INVERT = yes

TCP_PORT = 10000

 

# gbox config file

 

# gbox working mode

# 00 pure Emu

# 01 pure SoftCam (when card inside), Emu (when no card inside)

# 02 pure Net Client

# 03 Mixed mode !!!!! always use this !!!!!

G: { 01 }

 

# Display ECM messages on Konsole

# 00 don't show any ECM's

# 01 show only valid ECM's

# 02 show valid and bad ECM's with complete data display

C: { 01 }

 

# Display EMM messages on Konsole

# 00 don't show any EMM's

# 01 show only valid EMM's

# 02 show valid and bad EMM's with complete data display

M: { 01 }

 

# AutoUpdate

# 00 is ignored (default)

# 01 enable AU

# 02 Auto AU !!!!! always use this !!!!!

A: { 02 }

 

# Key update

# 01 update only new keys, default setting

# 02 update all keys (used for valid PMK checking)

U: { 01 }

 

# Hash pids

# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF

# 01 hash only pids with implemented algos and available keys !!!!! always use this !!!!!

H: { 01 }

 

# Key files folder

# 00 keyfiles in /var/keys

# 01 keyfiles in /var/tmp

T: { 00 }

 

# On Screen Display for the Multysystemcam on com1/com2

# 00 No OSD (default)

# 01 display Smartcard messages in Neutrino

# 02 display Smartcard messages in Neutrino new nhttpd format

# 03 display Smartcard messages in Enigma

O: { 03 } 127.0.0.1

 

# Logger and NET-mode UDP port Init

# 00 do not init UDP port

# 01 Init UDP port for IP, port, UDP

L: { 01 } 192.168.0.2 8017

 

# Trace/Debug

# xx yz ; xx=00 no konsole output

# xx yz ; xx=01 konsole output

# xx yz ; y=0 debug output (don't use)

# xx yz ; y=1 no debug output

# xx yz ; z=0 ouput to konsole

# xx yz ; z=1 output to /var/tmp/debug.txt

# xx yz ; z=2 Output to UDP (to capture with gboxt)

Z: { 01 10 } 192.168.1.29 802

 

# Option for VDR (Linux X86) only

# xx yy ; xx = dvb-s Card nummber

# xx yy ; yy = comport to use by that card

#V: { 00 01 }

 

bedankt alvast

ceasar

[ooi]

telnet 127.0.0.1 14000

[CEASAR W]

telnet geeft aan NOT FOUND

[Matchless]

telnet localhost 14000 mischien?

[CEASAR W]

Hallo matchless

localhost 14000 geeft ook not found

[ooi]

ik heb hem hier lopen met newcamd en als je dan in logt op je box en telnet 127.0.0.1 14000 dan krijg je de datum te zien en met 14001 krijg je de clients te zien

[Tech]

Dit staat in je cardserver gedeelte wat je hebt laten zien

[

DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14

SERVER_NAME = dbox

DEBUG_PORT = 14000

ENTITLEMENT_PORT = 14001

ADMIN_PORT = 14002

ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00

USER = dummy dummy lan localhost 12000

USER = dummy2 dummy2 lan localhost 12000

]

 

Ik mis in dit stukkie een au user,zet er bijvoorbeeld dit in:

USER = auto up lan localhost 12000 au

door er au achter te zetten geef je aan de de emm en ecm's die door deze user naar de emu gestuurd worden gebruikt mogen worden om naar de kaart te sturen (simplistisch gezegd)

In je newcamd.cfg moet die user dan uiteraard ook aanwezig zijn met naam en password, in dit geval "auto" met als pass word "up"

 

hieronder nog een voorbeeld zoals die in de cardserver zelf staat:

# two examples for additional AU users

# USER = dummy2 dummy2 lan dbox2 12000 au

# USER = dummy3 dummy3 au

uiteraard moet je de # die voor de regel staat weghalen, anders wordt het alleen als commentaar(tekst) gezien.

 

In je newcamd.cfg moet je dan ook zorgen dat die user aanwezig is,dat kan er zo uitzien:

CWS = 127.0.0.1 10000 auto up 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserv

Let wel op dat de DESkey in zowel de server(cardserver) als in de client (newcamd) overeenkomen.

Als je vervolgens via telnet connect naar de box en je de cardserver en newcamd processen stopt kan je meekijken of de zaak wel op elkaar connect.

cd /var/bin

./cardserver.dream

 

vervolgens zie je de cardserver starten, daarna start je newcamd door ./newcamd.ppc in te tikken (als die tenminste zo heet)

nu zie je een hoop rommel voorbijkomen maar je kan in elk geval ook zien of newcamd wel connect op de cardserver, in dit voorbeeld via poort 10000.

Als dit lukt krijg je ook een update op je originele kaart, welke image je gebruikt maakt niet uit.

Zolang de emu's goed geconfigureerd worden krijg je altijd een update.

[view]

Hallo @All,

 

met de Gbox 1.35 heb ik de update binnen gekregen.

De datum heb ik met Camd3 via telnet gecheckt.

 

Zie deze topic.

 

Groeten,

[Gast]

Gbox en cardserver gelijktijdig op dezelfde box gaat niet. Beiden willen de controle over de kaart. Wel kan je newcamd (zonder cardserver) naast gbox draaien. Dit vergemakkelijkt het controleren van de updates.